Re: 990 cat loader
 

do these look beefy enough ?

http://i830.photobucket.com/albums/z...r/PIC_1833.jpg

http://i830.photobucket.com/albums/z...r/PIC_1834.jpg

I've been working on these here and there . get a free min or to when the mill not busy :eek:

Re: 990 cat loader
 

Look's great Steve, Keep it up:D:D:D:cool::cool::cool:

Cheer's, Neil.

Re: 990 cat loader
 

So you're going with a motor /trans combo?

What the diff ratio gonna be?

Re: 990 cat loader
 

Joe , 3.3 :1 in the axles 2:1 in the drop box powered by 24v 2 speed dewalthammer/drill motor on 12V . I had an 18volt on it in the test vid . For me , I'm using what I have :o . I think It'll perform very well .:o

Re: 990 cat loader
 

Lookin good steve...

Re: 990 cat loader
 

You the man Steve!! that baby will be stout now. Great work as usual.

Re: 990 cat loader
 

thanks guys I'm really pleased the way it's coming out considering I'm using scrapped material for it :o the axles are cut from stock for wrap around bumpers that was .125 " to short :( . the counter wieght is cut from a 1" plate we found on a job back in the early 90's left by pipeliners the drill motor is from a drill I thought I could use on job sites for instaling elc. conduit on concrete walls for elc. serv. without lugging the gen. around (big fail) . So instead of it sitting around collecting more dust , why not put it to real use . I still need to make up the spool carrier ( in steel ) that'll have to wait till I get done with alum. so I don't mix chips . I took a hit on 3 out of 4 55 gal drums full of chips because of it :mad: .

Re: 990 cat loader
 

What sort of differential are you planning on using in this beaut Steve? I've been spending a lot of time on a design for a very small LSD for my loader build, but am thinking are they actually needed? With the weight these scale loaders end up, do they actually lift a wheel with open diff's? Sorry, just picking your brain here:o

Cheers

Glenn

Re: 990 cat loader
 

" do they actually lift a wheel with open diff's " :confused: not sure what you mean here , Glen I'm using the hpi savage steel diffs out of a nitro truck . they seem to handle some abuse . only time will tell .

I took some time this weekend for myself :o to unwind to figure out what to do to solve a production issue on hubs :confused: so I made some more parts for the axles . when running 2'nd op in the mill for the spool carrier on the same jig that I use for hubs , it still f'n off :mad: any how it was a long night :eek: but I managed to save the carriers with a pressed in brass sleeve . well enough BS :p:o I did take some so so pics :o

rear axle assm.
http://i830.photobucket.com/albums/z...r/PIC_1853.jpg

front and rear axle assm.
http://i830.photobucket.com/albums/z...r/PIC_1862.jpg

carrier and axles
http://i830.photobucket.com/albums/z...r/PIC_1859.jpg

http://i830.photobucket.com/albums/z...r/PIC_1860.jpg

http://i830.photobucket.com/albums/z...r/PIC_1861.jpg

pivot assm. and parts
http://i830.photobucket.com/albums/z...r/PIC_1855.jpg

http://i830.photobucket.com/albums/z...r/PIC_1856.jpg

http://i830.photobucket.com/albums/z...r/PIC_1857.jpg

steel sleeve over alum. for better wear protection
http://i830.photobucket.com/albums/z...r/PIC_1858.jpg

thanks for lookin

Re: 990 cat loader
 

Steve That a stout looking set of axles. How many scoops will this machine take to load the Mack.
Rob

Re: 990 cat loader
 

Thanks Steve, yep, I'm using savage diff's too;) I'm trying to contain the conversion in a standard savage diff casing so I can retro fit at a later date.

Very nice looking axles!

Re: 990 cat loader
 

prob. 6 heaped ,I know 1 heaped will load my little 10 wheeler and 1.5 brian in PA 's tri-axle

Re: 990 cat loader
 

Wow, Steve. The axles are incredible. Beautifully machined scale replicas. I drool everytime I see something like this. CNC is amazing.

Re: 990 cat loader
 

Yah, my other Mack got loaded by one out to Geneva Steel/Hecket slag pit, 1 partial scoop was 18 ton's of drain rock! LOL, Now that's a "Horse":D
I wonder where that picture is?:mad:

Cheer's, Neil.

Re: 990 cat loader
 

thanks Nate , CNC is cool but can cost you in the back pocket quick :eek:

yea there a big 1 Neil , I use to get loaded by a 992 with a spade nose in an old coal pit where they were crushing the lime stone over burden . 1 corner of the bucket 12ton for my lil 12' box . was something to see a tire higher then my cab :eek:

fixed my wheel jig :) thought I would never use this

http://i830.photobucket.com/albums/z...r/PIC_1866.jpg

http://i830.photobucket.com/albums/z...r/PIC_1864.jpg

10" face mill that came with the machine heavy as heck so you set it on the table and bring the spindle down to it

Re: 990 cat loader
 

Wow! Great job on these axles! As we said before, CNC is a thing, the man behind is another one ;) This loader will be a beast, can't wait to see it works!

Re: 990 cat loader
 

thanks B-train

I'm testing pic quality see what you guys think :o

Old

http://i830.photobucket.com/albums/z...r/PIC_1882.jpg

new

http://i830.photobucket.com/albums/z...ilder/9903.jpg

http://i830.photobucket.com/albums/z...ilder/9901.jpg

Re: 990 cat loader
 

Steve that is coming along nicely sense the last time I saw it. Ed

Re: 990 cat loader
 

wowza! great work! :D

Re: 990 cat loader
 

I guess that program I told you about worked.