Stupid mfu that keeps shutting down
 

I have had it with mfu's.This stupid unit keeps shutting down for no apparent reason.The battery is fully charged,I keep a volt meter handy.I only have the 4 servo leads plugged into the receiver.None of the servos are binding.I am ready to burn this sucker.I need a minute :eek:.

Thats all folks Ed

Re: Stupid mfu that keeps shutting down
 

What kind of radio are you using with it?

Re: Stupid mfu that keeps shutting down
 

I am using a futaba 9c 2.4 ghz.This is the same set up I ran with last year at Indy.No problem.I tried resetting the set up on the mfu,u know press white button and left stick up/down,left /rite. and so forth.This is bull crap.

Ed

Re: Stupid mfu that keeps shutting down
 

Ed, does it just run along, quit and restart itself while you are driving?

Re: Stupid mfu that keeps shutting down
 

hello Rob,
Yes.It will run for about 30 seconds and all of a sudden shut down,then restart and run for another minute,shut down.

Ed

Re: Stupid mfu that keeps shutting down
 

Are you running LiPos in the truck? My Futaba 4 channel 2.4 does the same thing. If I keep the throtle stick just forward of nuetral the truck will run fine until I forget and go to complete dead center on the stick and then it starts acting up again. It is the radio and not the MFU. Ask Travis about this. He told me it has to do something with the fail safe setup in the radio.

Lynn

Re: Stupid mfu that keeps shutting down
 

That happened to me.It was the radio, I think they should put a few more functions on these radios! It's beyond me why no one is buildin a radio JUST for us?? It took me days to git my atlas truck to work proper like w/a futaba 9 channel. Was ready to burn both of them.
Get away from it for awhile & let your head clear,then giver another shot!
Good luck!:D
FGD
Oh! Also had a bad servo one time that gave me a real run for it!
Might want to unplug one servo at a time,& try it.If all else fails.

Re: Stupid mfu that keeps shutting down
 

Lynn.I am running regular batteries,non lipo,s.I will try that trick with the dead center issue.
FGD, thanks for the advice.I did try that trick with removing one servo led one at a time.
Funny thing is,once this sucker runs,I drive it around the basement,in large circles,and I wait for it to sputter and then it dies,restarts,dies.I then pick it up.check battery voltage and I even tried to put a spektrum capacitor in the battery slot.No luck.I will stay at it and keep you all posted on what I find.THANKS EVERYONE for your support.This is a great board.Proud to be a member.

Ed

Re: Stupid mfu that keeps shutting down
 

Ed,

Jimmy had this w/ his black 379 and sent the MFU back to tamiya... they gave it a good report and sent it back... Jimmy put a different radio on it and it was a night and day difference.

Do you have another radio system to trouble shoot with?

Re: Stupid mfu that keeps shutting down
 

Re: Stupid mfu that keeps shutting down
 

Hey Ed, did you check the injection pump? Lol, I had the same problem with my mfu it was the radio I changed to airtronics and all good now! Keep us posted!

Re: Stupid mfu that keeps shutting down
 

One other thing, did you have a hard time binding your radio to your mfu? are all your switches in the normal?

I bought a new MFU a couple wks ago, darnest time trying to program it at first........too about 8 times, then, flipped my dual rate switch to off, programmed right up.

i also concur with the suggestions of checking the batteries. A ni-cad can die w/o any warning.......found that out this wknd too. My MFU would cut off every minute. took the old ni-cad out, then I ran a 5000mah 7.4 for about 6 hrs w/o any problems.

I know how aggravating it is.

Re: Stupid mfu that keeps shutting down
 

Heavy Duty, were you able to solve this problem? I am having the same problem where my MFU shuts off every 2-3 seconds then will restart. Repeat process. I tried doing the initial adjustment by pressing the white button then moving the sticks after the red light blinks, but nothing seems to improve.

I'm wondering if I got a faulty unit or if I just don't know how to use my 4-channel radio (Futaba 4YF 2.4GHz).

Re: Stupid mfu that keeps shutting down
 

Hello,I would suggest you switch radio's first.I went round and round and the problem was the radio.Good luck.

Ed

Re: Stupid mfu that keeps shutting down
 

Right you are!! I found out that 2.4GHz radio I was using wasn't "talking" with the MFU.

I just came back from my LHS and picked up a different radio (FM channel) and it all works fine now! :) Thanks!

Re: Stupid mfu that keeps shutting down
 

Seems a shame to have to go backwards and buy an old school FM radio, when you have a 2.4 giga-hertz radio. I think based on what I have read here, I find myself leaning more torwards Serovnaut. Can't really blame Tamiya. Back when the MFU came out, it was the age of FM.

Re: Stupid mfu that keeps shutting down
 

You can run them on 2.4 with no issues I myself have 1 RDS8000 and 3 vg6000's and the 8000 is 2.4 and works just fine and the dx6 works just fine the issue seams to be the futaba 2.4 not sure why but many have had issues with it and the MFU.. Now the RDS8000 comes in a ground 2.4 for semis and crawlers..

Re: Stupid mfu that keeps shutting down
 

TC is right. Futaba 2.4's are the problem. My Budwieser trucks does the same thing. I need to switch radios in it.

Re: Stupid mfu that keeps shutting down
 

Anyway to turn the failsafe mode off???????

Re: Stupid mfu that keeps shutting down
 

Re: Stupid mfu that keeps shutting down
 

:confused: Had to read that a couple times, Paul. Concrete, and planes?

Re: Stupid mfu that keeps shutting down
 

Has anyone tried the the RDS8000 for trucks/crawlers?

Re: Stupid mfu that keeps shutting down
 

LOL! great sense of humor TC:D Still learning:eek:
Cheer's, Neil.

Re: Stupid mfu that keeps shutting down
 

Yes 2.4ghz does not work well with our MFU. Some have said they got it to work but direct from us it is sketchy. Your best bet is a analog FM/AM setup.

If you are going to try 2.4ghz make sure it has analog trims, those seem to have the best chance.

Re: Stupid mfu that keeps shutting down
 

Yes, I have a Futaba 2.4 with analog trims. I had trouble at first till I realized the right joystick vertical trim cant be in the center position. I have it just south of center and all works well. If I place it in the center position the truck starts and stops all the time.
I purchased a DX6 recently, will be installing this winter. Hopefully it works well and I don't have to run it over or smash it with a hammer! Lol

Mario

Re: Stupid mfu that keeps shutting down
 

Re: Stupid mfu that keeps shutting down
 

I like my dx5 works every function perfect everytime with digital trims, and i never have to move or adjust my trims for all features to work.... i flip my hi lo rate up and my (r) stick will control the lights and hazards, or flipped down controls the horn, can shut down and start truck, control 5th wheel etc... Guess im just a lucky how i got it setup.

Re: Stupid mfu that keeps shutting down
 

2.4 will work with the MFU, u just have to make sure that ur settings are all centered when setting it up and go thru ur setup-motions slowly. I am using both the rds8000 and the 10g from airtronics will running dual-rates @ 100%, all functions works with just the sticks and no trim movement necessary.
I have talked a couple of guys thru on the futaba, but no personal experience with them.

Re: Stupid mfu that keeps shutting down
 

I said it will not work well with 2.4. We (Tamiya) recommend a AM/FM Analog radio for true plug and play use.

If you choose to use a 2.4 you may find issues, as the MFU was not designed for use with 2.4 radios.

Just be aware...

Re: Stupid mfu that keeps shutting down
 

if your using Spektrum equipment, different recievers have different levels of working well with the mfu. I know of one good fella that has pefect success with the combination that he worked into. Turns on, off, has all of it's functions - spektrum 2.4GHz

some of the issues with the spektrum stuff is the fail safe functions......maybe this is the issue with other 2.4 systems.

Re: Stupid mfu that keeps shutting down
 

with the MFU make sure your batteries are all good, as ones with a dead cell will probably play up on you... I have a 1400 Mah Nicad that I've earmarked as not to go back in my truck (metallic Jade Green Knight Hauler) again... but will probably still be okay for my Juggernaut 2 and TXT-1..

said battery ran okay for a few minutes then shut down and the clearance lights were flashing and I thought my MFU had blown up... so I charged up a battery up and it was right as rain! YAY!:D

that being said I am using the Futaba 4VWD radio gear... went for something simple.... but might change in the future...

Re: Stupid mfu that keeps shutting down
 

I was a bit worried after reading the thread, as I have a Futaba T6J 2.4Ghz radio and a MFC-02.

After plugging everything in, I was releived to see everything was working out of the box, for the execption of the blinkers.
After playing with a few things, all of a sudden the MFU turned off. Panicked for a bit, then realized the battery was slow. :o

Tonight I'll see about getting the blinkers going. I read a bit, and it seems that I have to use dual rates. Any hints?
Also, the radio has the option for Airplane or Heli, which changes default settings. Does that matter much which one I start with?

It is also possible to rotate the knobs? For example, have the L/R stick now be Up/Down and the Up/Down be L/R? Just wondering as it may be more convenient for my hands.

I will try to make the 2.4Ghz work as it is more convenient. If all else fails, I have a 4channel analog radio that I can use. I'd also rather have the 6 channel for the added options.

Re: Stupid mfu that keeps shutting down
 

To get your blinkers to work properly, you may have to do a couple of things:

1. adjust the position of your knuckle-rod on your servo horn.....
the blinking function will work at a mininum EPA setting, i.e 80% and above....this may vary slightly with radio brand. Having said that, if your servo rod is farther out to the end, you may get over-throw before your blinking function will work, thus binding your servo.

2. once you get you mechanics set, you can then adjust yoiur End Points to the desired throw all the way to 150% or as far as your servo will travel w/o binding.

Re: Stupid mfu that keeps shutting down
 

Ok, I'll give that a try.
I changed my radio's joystick configuration. Ratchet is now on the left stick, for left to right. That was a bigger job than I planned, and did not know how to go about it.

Re: Stupid mfu that keeps shutting down
 

How do I know if the servo is binding?
I moved the knuckle rod inward on the servo horn. I played a bit with the EPA settings for the steering (cha 1) and the option channel (ch 2 for my case). I also adjusted the D/R on ch 2 until I got the channel to work at switching the light functions while maintaining the high beam and horn function.
I assume I'm close, as for every ten times I try the blinkers, they work. :confused:
I also cranked the EPA on the streering to 140% to get more streering angle. Should I bring it back down and concentrate on ch 2 functions until I get the blinkers to work every time?

Re: Stupid mfu that keeps shutting down
 

Since I got into this hobby not long ago, all my radios have been 2.4 ghz. The first had digital trims so couldn't run the extra functions. The next had analog trims and I got all functions but the unit can have its bad days. Very sensitive, do something too quick or if everything isn't just right , you can't switch modes.
I have learned to deal with and can recognize when something isn't right but I knew if my wife was going to enjoy the hobby and enjoy her truck I needed something more reliable.
I heard that FM radios work well with a MFU but require an antenna unlike the 2.4 . I purchased a Airtronics FM radio for her truck.
I am absolutely amazed at how well and trouble free this radio works on this truck! All commands work on first attempt, engine never shuts down on its own! So easy to run! And the antenna issue was easy to deal with.... I secured the antenna wire to one of the exhaust stacks. As far as I see it, the stack is copper, not sure what the chrome may effect but, so far so good ( indoors :eek:)
For almost a year I just didn't know any better and lived with 2.4 issues. Never again, I will be switching my truck to FM also! .....
Anyone looking to buy a couple 4ch 2.4 radios?? :eek::D

Mario

Re: Stupid mfu that keeps shutting down
 

Robert and I have been plugging away at this issue.I have a futaba 10c with 2.4ghz,and I installed it in a new truck I am building and it shuts down and starts back up.I didn't give up this time,I swapped motors,batteries,and plugs.Same problem.Servoes are new.I then removed all plugs from the mfu to the receiver and plugged them in one by one.I left the plug from the mfu to the receiver labeled motorized legs,out of the receiver and MY TRUCK RUNS PERFECT.I reinstalled that plug and mu truck dies and restarts.I removed it and I AM STILL TRUCKING.No one fix fixes all,that is just my experience.Thank you Robert,

Ed

Re: Stupid mfu that keeps shutting down
 

I learned something too Ed, sometimes it takes two heads working together. I am glad you are up and working.

Re: Stupid mfu that keeps shutting down
 

Hi All, I was just rereading this thread, and wanted to add my two cents. I was running an older Futaba Conquest FM radio in my Globelinner for a long time. From the beginning, I was getting some minor glitching, and after trying several different things to fix it I ended up converting the radio to 2.4 ghz. the only difference is, like some others have found, I no longer need to use the trims. When I want to change something I just move the appropriate stick to the end of it's travel. I would like to say to janderson, you seem to be somewhat defensive about Tamiya's MFU. Instead of giving people a hard time about using 2.4 ghz radios with the MFU, wouldn't it make MORE SENCE TO REDESIGN THE UNIT TO WORK WITH NEWER 2.4 ghz RADIOS!!!:mad: After all if we as customers have issues with a product, we will look for something better, as some already have. Sorry for the rant, but I have an issue with companies that don't listen to consumers thoughts, when they depend on those consumers to survive.