AWD, worth it or not?
Just wondering what everybody's thoughts are here, there have been countless trucks built and shown on this site but a small percentage of them are AWD. Even some of the Heavy Haulers, Pacifics, Hayes, Macks, etc around here are not AWD and I'm sure they pull fine.
I'm getting the itch to build a King Hauler again. On one hand I want AWD, better traction is never a bad thing on a truck (plus cool factor), on the other hand I'm liking the thought of keeping things simple. I will say I did 8X8 on my Wedico Pete, I don't regret it but it came with it's fare share of challenges. |
Re: AWD, worth it or not?
If you cant decide on whether to or not build a rig with front diff lock so you have the best of both worlds for on road off road
|
Re: AWD, worth it or not?
To me it depends upon how and where you are going to use the truck. If using it on dirt, AWD with locked diffs is a must for any truck. You need as much traction as you can get. If using it at Indy or any other site with the rubber and carpet, you should get by with just rear wheel drive.
|
Re: AWD, worth it or not?
from my experience having both trucks there is pros and cons of each.
RWD single axle trucks are only good for on road applications. You can lock the rears but still only gets you so far. Best turning radius. RWD tandem trucks go more places then singles, You can lock the front or both axles for more off road or sandy conditions and get some decent turning radius out of them. AWD trucks go pretty much anywhere ground clearance will let them. Turning radius is not great on them however. -TLT axles work good, so do highlift axles. Highlift axles stick out a hair more then TLT but easier to find and more upgrades. Also you can lock and unlock highlift axles with the grub screw that is a factory option. just requires the hex lining up through the sight hole and removing it. TLT's you have to take apart to lock and unlock. regardless which axle, tamiya tundra highlift springs are the best to get them centered in the stock spring hanger locations. |
Re: AWD, worth it or not?
How would you run awd in a king hauler with the stock trans? No front output shaft and no clearance to fit a drive shaft from the rear
|
Re: AWD, worth it or not?
Quote:
Here is how the Late, Great Freedygeardrive did it; http://i301.photobucket.com/albums/n...mppics5476.jpg http://i301.photobucket.com/albums/n...mppics5479.jpg http://i301.photobucket.com/albums/n...mppics5468.jpg Another idea: http://www.scale4x4rc.org/forums/att...1&d=1221072061 Here is how Smallhaul Scott did his; http://i240.photobucket.com/albums/f...end-tranny.jpg http://i240.photobucket.com/albums/f...n/tranfer2.jpg http://i240.photobucket.com/albums/f...motortrans.jpg Of coarse a using different transmission would be easier, one with a built in transfer case. As they say there is more than one way to skin a cat. |
Re: AWD, worth it or not?
Very good stuff there, thanks. I see the tranny for a high lift f350 has front and rear outputs, but has a different mounting method. Maybe the cases are the same and I can swap them out, or make up some brackets
|
Re: AWD, worth it or not?
This 6wd GL gets around great pulling a pup with all diffs open, of course the tires are a little bigger than stock, which helps I'm sure. I grafted a HiLift t-case on the back of a stock Tamiya 3spd. TLT front axle. Hand drilled the stock springs, which sit on top of the axel.
http://img.photobucket.com/albums/v1...psd3a91ef6.jpg |
Re: AWD, worth it or not?
Very cool. Are the cases for a highlift and KH the same?
|
Re: AWD, worth it or not?
No, they're shaped differently.
Both these trks run the Wedico dual motor coupler with twin 12v Buehler motors. I was able to make an adapter so the stock semi trans would work, but the way the HiLift trans is made - no chance with that one. |
Re: AWD, worth it or not?
No Bueno. If you were going to make an awd rig with a 3 speed, how would you do it?
|
Re: AWD, worth it or not?
What kind of trans is that in the picture second from
Last? |
Re: AWD, worth it or not?
That is an RC4WD 3 speed but way over priced your better of with a high lift trans or a stock 3 speed and and an axial trans for a transfercase which also gives you a 3:1 gear reduction. If your fine with just one gear use an RC4WD R2.
|
Re: AWD, worth it or not?
Thanks, didn't know rd4wd made 3 speeds, just saw 2 and the auto cvt. I just picked up a high lift but the mounts are different. I'm probably going to use spacers to lift the trans up as much as I can to get some more clearance. The 2 flanges on the bottom of the stock 3 speed that hold the case together sit right in front of the front axle input shaft. What are your thoughts on adding a small servo shift 2 speed hi low trans to get 6 speeds?
|
Re: AWD, worth it or not?
6 speed does have a cool facter but most of the truck shows dont have enough room to show it off that well. Since you have the high lift trans just make some mounts and use it. The highlift trans is a great trans with more gear options than the stock trans.
|
Re: AWD, worth it or not?
I'm using a motor mounted 7:1 gru to really slow it down. 6 or even 9 speeds would be awesome, well worth the investment in my opinion.
|
Re: AWD, worth it or not?
Alright I've found a solution for anyone looking to get more than 3 gears and awd. RC4WD makes a 3 speed transfer case that I'm going to mount behind the stock tamiya trans and use a short driveshaft to connect the two. This should give me 9 gears using 2 3 way switches, just like the old twin stick in the real ones
|
Re: AWD, worth it or not?
Quote:
I have a transmission I bought from RC4WD probably 4 years ago, I know they don't make it anymore but it is a two speed. I thought it was an R2, looks like this; http://tracgear.com/product/rc4wd/cu...n/R2/g11/3.jpg What is it if not an R2? I also have an R2 single speed, wide gear, HD version. |
Re: AWD, worth it or not?
Quote:
If you want away from those bolts holding the case together you can buy an aluminum case that replaces the plastic one. I have one of these, there is no bolts in it at all. $65.00 on the ole eBay. http://i.ebayimg.com/images/g/jy0AAO...AxW/s-l500.jpg |
Re: AWD, worth it or not?
Izzy's daycab inspired me to build a Tamiya 2 speed with all the upgrades. So far I have bought the brass helical gears, stainless synchronizers, aluminum case and aluminum heat sink end plates. Not everything is here yet though. There are only two other upgrades I can think of, a new longer shaft so you can drive off both ends of the trans mission and a PMD 4:1 reduction. I shouldn't have spent all of this on this transmission, I should have just bought a Veroma 3 speed with built in transfer case and had a better transmission.
I did have a hair brain idea, what if you had the longer shaft and a reception on each end of the transmission? Would be cool, but too long and too expensive. Again Veroma! http://www.gardentrucking.com/pix/Originals/t1225.jpg And here is the Veroma; http://i296.photobucket.com/albums/m...psa49a91e0.jpg |
Re: AWD, worth it or not?
Great Decision...Veroma is the way to GO ! Top of the line. :cool:
|
Re: AWD, worth it or not?
Have they improved the Veroma gbox? I know of people who've had trouble when using it in trucks pulling heavy dumptrailers.
|
Re: AWD, worth it or not?
I have never had any troubles but I have always babied my truck.
|
Re: AWD, worth it or not?
My Veroma is in my Wedico, thinking about putting one in a Tamiya.
|
Re: AWD, worth it or not?
AWD is definitely worth it if your going to run off road loaded or empty. If your going to build it and put it on a shelf or run it on pavement only on dry sunny days don't bother it's not worth the cost and build time.
Another less expensive but very strong option is using an Axial SCX10 transmission as your transfer case, you can pick them up on eBay for around $40.00. That gives you a 3:1 reduction. Connect it to the 3 speed as shown below. The stock silver can works fine and I wouldn't go any deeper than a 55 turn motor. I've hauled some pretty heavy loads on this with a heaping dump box and it runs through sandy soil with ease. http://i1116.photobucket.com/albums/...psbzgaaltp.jpg. http://i1116.photobucket.com/albums/...ps3umcjo2j.jpg Note the GRU in this photo was removed and I've never ran it in this or any other truck. http://i1116.photobucket.com/albums/...psmga99c9z.jpg http://i1116.photobucket.com/albums/...psxmoqb5bb.jpg This is one fun truck to drive! |
Re: AWD, worth it or not?
Quote:
|
Re: AWD, worth it or not?
Quote:
|
Re: AWD, worth it or not?
Thanks Travis, I understand how it works, it's perfect for what I want to do, will give me 6 gears when coupled to a stock tamiya 3 speed with the option to go 2/4wd
|
Re: AWD, worth it or not?
Simple question to make sure I got my gear ratios right. 1:9 would be 1 turn input equals 9 turns output. Wouldn't that increase the output speed 9 times? If it's a true reduction gear shouldn't it be 9:1 instead of 1:9?
|
Re: AWD, worth it or not?
The six speed concept is a cool idea but I don't think that transfercase is going to let you shift on the fly by any means. If you are wanting to replicate the old truck transmissions your effort is going to be lost in translation with that setup. Just my opinion.
|
Re: AWD, worth it or not?
http://store.rc4wd.com/Bullet-3-Spee...se_p_3259.html
That would be 1.9:1, as in 1.9 turns input to 1 turn output. |
Re: AWD, worth it or not?
I'm glad someone is paying attention.
|
Re: AWD, worth it or not?
Quote:
Does anyone have other experiences? |
All times are GMT -4. The time now is 12:33 AM. |
Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.