Anyone know where to buy these grousers please?
 

Hi all, dozerbuilder from Australia here. I'm in the early planning stages of an RC bulldozer with semi-U and single tine ripper build in 1/16th. I wasn't actually planning to open up a build-thread just yet because it's too early - I am really early in the planning and drawings though when I get going I plan to run the entire build thread here.

I have the usual problem, grousers and track links. I have been scouring the forums and net for weeks studying the options for the track links and grousers. I'm looking at a grouser plate width of about +2" less than -2.5".

I saw these (see attached pics) on a "1 /12 crawler version KAT-2 full metal hydraulic tipper mud head engineering vehicle model" on the net. It's in Chinese and though I've been to China twice, that doesn't help with the communication via the net.

So my question is; does anyone among the learned fraternity here know if these grousers and links are available. Note they are the single bar dozer type, not 2-bar or 3-bar excavator type.

Thanks in advance,
Dozerbuilder.

Re: Anyone know where to buy these grousers please?
 

Like this?
http://www.rcbrmin.com/excavator-112...ces-p-683.html

Cheers,
Ap

Re: Anyone know where to buy these grousers please?
 

It's the correct tracks Ap is referring to. It possible to get them for better prices than on the rcbrmin webshop, through agents in China. But the ones here at the forum who has experience with it, can speak for them self.
Tracks are 50 mm wide.

Re: Anyone know where to buy these grousers please?
 

Thank you AP, that's exactly the ones I was referring to. I'll see if I can order a just few and see how they and the track frame drawings tie-in.

Cheers

Re: Anyone know where to buy these grousers please?
 

That's the ones alright. 50mm grouser plate width (2.00") as you say. Now to hunt them down.

Cheers.

Re: Anyone know where to buy these grousers please?
 

has anyone ordered these and what are they like.

Re: Anyone know where to buy these grousers please?
 

j-hammer, as a result of the helpful answers here to my request for information, I ordered a dozen of the single-bar grousers (which have an attached 1-piece link arrangement) here: http://www.rcbrmin.com/excavator-112...ces-p-683.html.

I only ordered a dozen to start to assess their practicality for my proposed build and also so I could roll them around over half the circumference of a sprocket or front idler to check the pitch.

So I'll be happy to report back when I get them. Said to be 9 days by air from China to AUS so assuming all goes well.

Then I'll decide if I'll use roller #80 offset roller chain joiner links and spot-welded custom stamped plates or the ones I ordered.
Cheers

Re: Anyone know where to buy these grousers please?
 

UPDATE.
Well I got an email from despatch at rcbrmin today to say they are shipped so I'm pretty happy with the communication and prompt service..

Cheers

Re: Anyone know where to buy these grousers please?
 

UPDATE 2: Well, I received the grousers from RCBRMIN today and I can say I'm pretty happy with the service and product from them.

The grousers are nice work!. The plate and links are cast as one piece as can be seen in the photo. They are strong, I could not damage twist or bend one hard as I tried by hand-test destruction so they'll certainly take a pair of 12v wipers motors behind them. For me they scaled almost perfectly for my proposed build, you can see in the attached pic they match nicely on the 1/16th drawings for an 800 mm wide grouser in 1:1 = 50mm in 1/16th. I'll start a build thread if I proceed with the build, I'm overwhelmed in brain-deep 3D and 2D CAD drawings at present.

Re: Anyone know where to buy these grousers please?
 

And I forgot to mention that most important measurement of all = "pitch" it's 18mm.

Re: Anyone know where to buy these grousers please?
 

Looks good) The KAT company have designed some fine track shoes that sells for a reasonable price, which is the only products from them I recommend to spend money at.

12V viper motors? Have you checked out http://mfacomodrills.com/

Re: Anyone know where to buy these grousers please?
 

Thanks for the link. Wiper motors have good low rpm torque, are relatively simple in design, easily mounted, easily obtained and can be speed controlled using a potentiometer or an off the shelf radio shack type pulse width modulator unit. (I'm getting a little ahead of myself here, I'm still in early drawing stage.)

Re: Anyone know where to buy these grousers please?
 

any idea if these will fit to carson lr loader with out moding ?