RC Truck and Construction

RC Truck and Construction (https://www.rctruckandconstruction.com/index.php)
-   Electronics tech (https://www.rctruckandconstruction.com/forumdisplay.php?f=102)
-   -   Turnigy 9x for dozer questions (https://www.rctruckandconstruction.com/showthread.php?t=8083)

baker3 12-20-2013 10:45 AM
Turnigy 9x for dozer questions
 
Anyone using this radio with info is greatly appreciated. I am trying to mix channels to control all steering and throttle from the left stick. I have my ESC's for the two servos plugged into the CH1&2. So far I can get both tracks to move forward and back but unable to steer. Any help? I am a complete noob to this area

doodlebug 12-20-2013 02:09 PM
Re: Turnigy 9x for dozer questions
 
The only suggestion I have is to use a Sabertooth controller, they have the mixing built in,
http://www.dimensionengineering.com/...abertooth2x5rc Hope somebody else will chime in too!
Cheer's, Neil.

Lil Giants 12-20-2013 03:16 PM
Re: Turnigy 9x for dozer questions
 
Your radio came with a manual, did it not? Look under channel mixing. ;)

Tip: the throttle channel is Master and the steering is Slave. It'll be +100 & -100.

I've never owned a Turnigy radio. For my Spektrum radio, if it's steering the wrong way, then I can either switch the + & - values or reverse the travel of steering ch itself.

kenobi 12-20-2013 06:01 PM
Re: Turnigy 9x for dozer questions
 
This may be of help, there are tons of them on YouTube
http://youtu.be/YNx9DHySD9A

doodlebug 12-20-2013 07:39 PM
Re: Turnigy 9x for dozer questions
 
Quote:
Originally Posted by oztruck (Post 100074)
TURN ON RADIO
go to display. using your display find out which stick operates your
RUDDER AND ELIVATOR. Change stick type till you get then where you want them.
Go to V-TAIL
State = ACT
ELE1 = -100
ELE2 = 100
RUD1 = 100
RUD2 = -100

Go back to display and watch how they work.

Cheers Chris.
HMMMMM! all this programing makes my radio a dinosaur :lol::lol::lol:
Cheer's, Neil.

baker3 12-28-2013 05:42 PM
Re: Turnigy 9x for dozer questions
 
Quote:
Originally Posted by oztruck (Post 100074)
TURN ON RADIO
go to display. using your display find out which stick operates your
RUDDER AND ELIVATOR. Change stick type till you get then where you want them.
Go to V-TAIL
State = ACT
ELE1 = -100
ELE2 = 100
RUD1 = 100
RUD2 = -100

Go back to display and watch how they work.

Cheers Chris.
I tried what you said and I still cant get it. I have the left track running off channel 2, Right track off channel 3 and the rams are controlled with the Rudder and Aileron. Do I have to plug the tracks into an Aux slot?

Brel 12-28-2013 06:11 PM
Re: Turnigy 9x for dozer questions
 
have look at this forum http://openrcforums.com/forum/index.php (you may have to register) they have lots of stuff on there about the 9X radio

kaptain Jack 12-29-2013 08:57 AM
Re: Turnigy 9x for dozer questions
 
That's not exactly what you looking for,but still can be usefull
http://www.youtube.com/watch?v=Oi7jRcsfXB8

baker3 12-29-2013 10:24 AM
Re: Turnigy 9x for dozer questions
 
So for anyone having similar troubles, I finally figured it out. I have my radio set to "acro". I then set the stick type to the Rud and Ele to use channels 2 and 4 which my tracks are plugged into. Then as Oztruck said, go to V-Tail and adjust the parameters to what he said.


All times are GMT -4. The time now is 12:08 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.