Mack DT 3rd rebuild
 

First build the little VMG axles were too weak:

http://i240.photobucket.com/albums/f...in/1010229.jpg

http://i240.photobucket.com/albums/f...n/P1010276.jpg

http://i240.photobucket.com/albums/f...n/P1010265.jpg

Second build worked great but, I wanted more off-road traction.

http://www.youtube.com/watch?v=kn_ALo_UnPw

I wanted to add a driven axle to the front so I made a dual output shaft box for the back of my Tamiya trans which I posted on another thread:

http://i240.photobucket.com/albums/f...end-tranny.jpg

http://i240.photobucket.com/albums/f...de2-tranny.jpg

I have the front axle & trans finished, I'll post up more pics soon.

Re: Mack DT 3rd rebuild
 

The transfer unit that I made is done but, I won't seal it up with silicone until I abuse it for a while.

http://i240.photobucket.com/albums/f...in/tranfer.jpg

http://i240.photobucket.com/albums/f...n/tranfer2.jpg

http://i240.photobucket.com/albums/f...xin/bottom.jpg

I also dropped the trans down so that the cab would sit right on the frame.

http://i240.photobucket.com/albums/f...motortrans.jpg

http://i240.photobucket.com/albums/f...in/cableft.jpg

http://i240.photobucket.com/albums/f...n/cableft2.jpg

http://i240.photobucket.com/albums/f...in/cabrear.jpg

http://i240.photobucket.com/albums/f...n/cabright.jpg

Re: Mack DT 3rd rebuild
 

I bought the 10" Dump that FGD was selling for it.

THANKS FRED!

http://i240.photobucket.com/albums/f...xxin/mleft.jpg

http://i240.photobucket.com/albums/f...xin/mfront.jpg

http://i240.photobucket.com/albums/f...xxin/mrear.jpg

http://i240.photobucket.com/albums/f...xin/mrear2.jpg

http://i240.photobucket.com/albums/f...xin/mright.jpg

http://i240.photobucket.com/albums/f...xin/munder.jpg

I still have a lot of work to do. The bed is just sitting on the frame. I have to make the cable lift system for it, find better steps, tanks & front bumper.

Re: Mack DT 3rd rebuild
 

Scott the truck is comeing together nicely and you are going to realy like the front driven axle.

Travis

Re: Mack DT 3rd rebuild
 

looking really good man!!!

Re: Mack DT 3rd rebuild
 

That baby looks scale now.Super nice job lowerin the cab to where it belongs. Only one problem.You might have to change your forum handle.
Something like large haul. Can your skid steer load that workhorse? Or do you have to ramp it?
Keep up the good work!
FGD

Re: Mack DT 3rd rebuild
 

Thanks Joe!

Thanks Travis, I can't wait to get it finished so I can see how well it does off road.

Thanks Fred! No, the skid steer would never reach. I could load it with the dragline in about 15 minutes..:rolleyes: I think I'll need a front end loader soon.:)

Re: Mack DT 3rd rebuild
 

Will you be converting a Tonka Mighty Loader? That would be cool!

Re: Mack DT 3rd rebuild
 

I forgot, Awesome Truck!!

Re: Mack DT 3rd rebuild
 

This is going to be a nice looking dump. Much better looking with that cab dropped down where it should be.

Re: Mack DT 3rd rebuild
 

I agree. Sweet little dump truck, even though it's not that small! Bigger then the Tonka converted one you did. :D

Re: Mack DT 3rd rebuild
 

Re: Mack DT 3rd rebuild
 

Thanks a LOT Fellas for all of the positive remarks!

I just got some needed parts from Greg (Losiassociated) today to keep moving on the rebuild.

I still need to come up with nice bumpers for it front and rear. I might look for some 1/4" aluminum and try to make a front bumper. But, I'll probably get the dump working first to make sure it is ready to haul at the Brookville meet.

Re: Mack DT 3rd rebuild
 

truck is looking great, the new box fits on there nice. really like the transfer case, nice and simple.

Re: Mack DT 3rd rebuild
 

:eek:now that box makes the difference :thumbsup: great work Scott ;)

IHSteve

Re: Mack DT 3rd rebuild
 

Scott your Granite looks great keep[p up :)the good work. Ed

Re: Mack DT 3rd rebuild
 

Thanks All!

I got some more done. It really needed a new frame so, I used a set of stock KH rails. You can really see how short it is when it is sitting on the uncut frame.

http://i240.photobucket.com/albums/f...maxxin/3-2.jpg

I looked at a bunch of pics on the net to get the rear length right, I am happy with it.

http://i240.photobucket.com/albums/f...maxxin/4-1.jpg

http://i240.photobucket.com/albums/f...maxxin/5-1.jpg

Still needs tanks & steps. I found some pics of Granite DT's that have long slim tanks that I am guessing is for better ground clearance and I might make something like that.

http://i240.photobucket.com/albums/f...maxxin/6-1.jpg

http://i240.photobucket.com/albums/f...maxxin/7-1.jpg

I did make a set of pipes using King & knight exhaust parts.

http://i240.photobucket.com/albums/f...maxxin/2-2.jpg

Re: Mack DT 3rd rebuild
 

Made some more progress. I got Fulda tires for it and filled them with bb's and glued them with CA. So far the truck weighs about 9 lbs without the battery.

http://i240.photobucket.com/albums/f...bumperleft.jpg

I also made a hefty front bumper for it (1/8" thick aluminum stock) and used solid 1/4" square stock running inside the frame rails to make it nice & strong.

http://i240.photobucket.com/albums/f...xin/bclose.jpg

http://i240.photobucket.com/albums/f...tmaxxin/b2.jpg

http://i240.photobucket.com/albums/f...tmaxxin/b3.jpg

http://i240.photobucket.com/albums/f...xxin/bront.jpg

Re: Mack DT 3rd rebuild
 

Truck looks great! The tires look the part for sure. A tilt top tag trailer would look really good in tow.

Re: Mack DT 3rd rebuild