Aeromax AWD flat bed.
 

I started this build to test out the Integy axles and as the title says it is an Aeromax with a flat bed, well sort of.

http://i574.photobucket.com/albums/s...4/100_1859.jpg

http://i574.photobucket.com/albums/s...4/100_1860.jpg

http://i574.photobucket.com/albums/s...4/100_1854.jpg

http://i574.photobucket.com/albums/s...4/100_1855.jpg

http://i574.photobucket.com/albums/s...4/100_1863.jpg

http://i574.photobucket.com/albums/s...4/100_1862.jpg

http://i574.photobucket.com/albums/s...4/100_1861.jpg

http://i574.photobucket.com/albums/s...4/100_1865.jpg

http://i574.photobucket.com/albums/s...4/100_1866.jpg

http://i574.photobucket.com/albums/s...4/100_1867.jpg

http://i574.photobucket.com/albums/s...4/100_1870.jpg

http://i574.photobucket.com/albums/s...4/100_1869.jpg

http://i574.photobucket.com/albums/s...4/100_1871.jpg

http://i574.photobucket.com/albums/s...4/100_1872.jpg

http://i574.photobucket.com/albums/s...4/100_1868.jpg

Travis

Re: Aeromax AWD flat bed.
 

http://i574.photobucket.com/albums/s...d/100_1873.jpg

http://i574.photobucket.com/albums/s...d/100_1875.jpg

http://i574.photobucket.com/albums/s...d/100_1883.jpg

http://i574.photobucket.com/albums/s...d/100_1882.jpg

http://i574.photobucket.com/albums/s...d/100_1881.jpg

And here is the sort of a flat bed part.

http://i574.photobucket.com/albums/s...d/100_1888.jpg

http://i574.photobucket.com/albums/s...d/100_1885.jpg

http://i574.photobucket.com/albums/s...d/100_1884.jpg

http://i574.photobucket.com/albums/s...d/100_1876.jpg

http://i574.photobucket.com/albums/s...d/100_1878.jpg

http://i574.photobucket.com/albums/s...d/100_1877.jpg

So when there is a trailer that needs a little more truck to pull it just pop off the bed and you have an AWD work horse.:D

Travis

Re: Aeromax AWD flat bed.
 

Good eye there Oztruck.:D It is one of many trucks I have in the build process.

http://i574.photobucket.com/albums/s...k/100_1858.jpg

Travis

Re: Aeromax AWD flat bed.
 

Looks good there Travis:D Is the front axle cvd or something else?could you show turn radius full lock on both axles? where did you source them from?

Re: Aeromax AWD flat bed.
 

Chris they are form Integy or you can get them from Tower Hobbies as well.

When I was playing with the axle before I installed it the knuckles will turn about 70deg and still turn free so the only real limiting factor is the off set of rim and the tire hitting the springs. With a stock front rim and a round drive hub the track width is the same as a stock axle and the turning radius is better than stock.

Travis

Re: Aeromax AWD flat bed.
 

Nice, i've been wondering about those axles :)

Re: Aeromax AWD flat bed.
 

Ok thanks i did find them at integy.There is a set on the bay that has lockers on all 3 axles but they are higher than the integy ones:( Im wanting to build a truck to put one of Izzy's dumps on

Re: Aeromax AWD flat bed.
 

Ahh, a Mack CH 6x6! Sweet! How many more of these cabs do you have? I tried getting a crate, but the seller wouldn't respond to emails....

Re: Aeromax AWD flat bed.
 

I think you will like them.

Travis.

Re: Aeromax AWD flat bed.
 

I just threw the Mack out there since Oztruck ask about it. The Mack will just be a tandem drive with a dump box. I kept putting a dump box on my black Mack while I was building it and just could not resist building one. This is the only other one I have besides the Black Mack and I will tell you it cost me a good chunk of change to get it.:eek: We tried buying some of these trucks and every body has them in stock until you order them then they want to ship you some thing else instead.


Travis

Re: Aeromax AWD flat bed.
 

Travis tks for posting! Those axles look pretty BOSS!!!

Can you lock the axles?

Re: Aeromax AWD flat bed.
 

Thanks Rod and I am sure you could lock them but I just have not taken one that for apart yet.

Travis

Re: Aeromax AWD flat bed.
 

That looks really nice Travis good job man.


John

Re: Aeromax AWD flat bed.
 

And another powered steering axle with the tie rod on the wrong side of the axle!!! ...you guys, do you not peel the tires off in a sharp turn, nor do you notice how it seems to slide more than it carves? :rolleyes: :D

Re: Aeromax AWD flat bed.
 

Joe, I'm not quite sure I understand the logic behind the tie rod location. Behind, or in front, what matters most is the proper ackerman steering geometry, isn't it?

Re: Aeromax AWD flat bed.
 

Yes you're right Nathan, the Ackerman principle. Tie rod infront completely screws that up.

Re: Aeromax AWD flat bed.
 

I like the versatility Travis. Really good idea for someone who can't have several trucks, leaves the options open for several different functions. Thumbs up.

Ben

Re: Aeromax AWD flat bed.
 

Explain to me the logic behind how being in front or behind the axle makes a difference . Maybe because the way the modle axle is setup . But , in real life it doesn't make a difference as too the effect of the steering . I've seen it both ways . I believe the reason for tucking the tie rod behind the axle is more of a protection thing , whereas the axle is designed to take bending loads while the tie rod is designed for tensional loading . To put in simple terms that spinaly lil tie rod will bend fairly quick if it were to get snagged . As for sliding there are a# of factors : weight distribution , locked rears , length of truck . My paystar has the tie rod in the front , being it's long and heavy , I have no steering issue whatsoever . FWIW , it's no shelf queen

on edit : having review the Ackerman design yes in principal it should be in the back when ever possible . but also the position of the steering arm is critical to have the true Ackerman effect . If not followed , it ( in theory ) wouldn't make a difference as to what side of the axle you put the tie rod on . I would like to get a pair of these axle's just to see what can be adapted to them :rolleyes:

Re: Aeromax AWD flat bed.
 

http://www.beam-wiki.org/wiki/Steeri...erman_Steering

http://www.beam-wiki.org/w/images/th...ering_Path.GIF

The pic above, say up is forward. Notice how the left tire (inside wheel of the turn) is so much sharper than the right? Then picture down is forward & you'll notice the opposite has happened.


I got this lil red dump trk that Freddy built, 1st load on it I peeled the tamiya floats off the rims (WTF?!). Thinking the floats didn't have enough sidewall strength, I changed them out to the Tamiya standard tire & the same thing happened.... turn the trk over for a look see & yep! tie rod infront! :rolleyes: Something else that I took note of was this shorter wheelbase dump couldn't make turn before the entry level to the wooden ramp by the water heater. My KH which is a 6x4 too & the w/b 3.25 inches longer does make the turn without backing up.

I built some hay wagons from semi truck frames, I turned the front axles around so the tie rod is in front, made it easy to cut the tie rod tube, weld in another ball joint & bolt each side directly to the hitch tongue for easy control of the steering... what a mistake!!! you should see this thing rip up the ground while turning sharp loaded, the two tires fighting each... ofcourse the wagons still make a reasonably sharp b/c the tractor pulling them ultimately decides that, but the outside tire of the turn really rolls up the dirt b/c it's way too sharp!

Heck, even my combine with rear steering has the tie rod behind the axle. Combine cuts pretty sharp going forward, much wider turn in reverse, it will not follow the same track.

Try putting your tie rod behind the axle Steve, I'll put money on it that it turns shorter & smoother.

Re: Aeromax AWD flat bed.
 

I'm about to make new knuckles for it doo to the weight I'm twisting the steer arm that you put the extension on for the drag link . on the FDM's and most real axles you have steer arms on the top and bottom of the axle . I'd like to doo the same to eliminate the extension . With a full load of logs , I might be taxing out the plastic axle . I just might put a pair of these on it . Would've been nice if the ratio was the same :( . But maybe these rears will werk better with my hendrixson walking beam :confused: