Forum: Construction Equipment
11-22-2017, 07:02 PM
|
Replies: 62
Views: 16,556
Re: ADT build
Sure, that's super easy. It has a standard servo lead. Just connect that to your receiver as normal. It also has a 12V power (red/black) and you just connect these directly to your 3S battery.
...
|
Forum: Construction Equipment Tech
11-21-2017, 06:12 PM
|
Replies: 23
Views: 7,020
|
Forum: Construction Equipment
11-21-2017, 06:10 PM
|
Replies: 62
Views: 16,556
Re: ADT build
You can get any gear motor to be an RC servo by using a controller board like this one:
- https://www.ebay.com/itm/172264924286
(there are more types)
With this setup, you don't even need to...
|
Forum: Construction Companies & Worksites
11-21-2017, 05:40 PM
|
Replies: 2,507
Views: 964,089
|
Forum: Construction Equipment
11-20-2017, 07:51 PM
|
Replies: 62
Views: 16,556
Re: ADT build
Very nice build!
I'm looking forward to the updates with a lot of anticipation!
For some while I've been pondering with an ADT build myself, but it likely won't happen for real for a few...
|
Forum: Construction Equipment Tech
11-20-2017, 07:39 PM
|
Replies: 23
Views: 7,020
|
Forum: Construction Companies & Worksites
10-18-2017, 03:46 AM
|
Replies: 565
Views: 179,112
Re: Skeeters contracting services
You could put the hubs on the motor axle the wrong way and just drill a wide hole in the center of the epoxy, wide enough for the axle and hub cylinder to fit in. That would save you half an inch on...
|
Forum: Construction Companies & Worksites
10-16-2017, 04:27 PM
|
Replies: 565
Views: 179,112
|
Forum: Construction Companies & Worksites
10-12-2017, 05:34 PM
|
Replies: 565
Views: 179,112
Re: Skeeters contracting services
I've used Li-ion batteries in some robotics projects and a couple of RC-builds:
- Bruder MAN truck: http://www.scale4x4rc.org/forums/showthread.php?t=80393
- Bruder Delta loader:...
|
Forum: Construction Companies & Worksites
10-04-2017, 05:34 AM
|
Replies: 565
Views: 179,112
Re: Skeeters contracting services
I've been thinking about the same thing! I've been prototyping with adding steel wire 4mm) inside the wheels, but your lead approach looks more doable. The handling will be much better with the added...
|
Forum: Construction Equipment Tech
09-16-2017, 04:10 PM
|
Replies: 23
Views: 7,020
|
Forum: Construction Companies & Worksites
08-29-2017, 04:34 AM
|
Replies: 565
Views: 179,112
Re: Skeeters contracting services
Hi Skeeter!
Your two printing problems are very common problems, but they can be fixed. One is actually very easy to fix :-)
Overhangs drooping:
- The 3D-printer cannot put molten plastic in...
|
Forum: Construction Equipment
08-28-2017, 03:48 AM
|
Replies: 43
Views: 22,186
Re: Bruder 574 RC conversion weekend project!
I put the original part on a sheet of paper and photographed it from directly above (perpendicular to the sheet plane).
Then I import the image into fusion 360 as an canvas image and project it on...
|
Forum: Construction Equipment
08-28-2017, 03:43 AM
|
Replies: 43
Views: 22,186
Re: Bruder 574 RC conversion weekend project!
Yes, it does take time to get to know 3D printing i general and also the characteristics of your own machine. But if you stick at it, you'll get it.
I always print in ABS, but it should print fine...
|
Forum: Construction Equipment
08-27-2017, 05:06 PM
|
Replies: 43
Views: 22,186
Re: Bruder 574 RC conversion weekend project!
Thanks, Frizzen! :-)
I found another listing on Ebay that included the table of sizes for the different gear boxes:
- http://www.ebay.com/itm/200910274596
For the 24rpm gear box, it's 25mm.
...
|
Forum: Construction Equipment
08-27-2017, 04:41 PM
|
Replies: 43
Views: 22,186
Re: Bruder 574 RC conversion weekend project!
It's a little difficult to measure when it's in one piece. I'll try to measure it for you the next time I have it dismantled.
I think I would actually use motors with a little higher RPM. I chose...
|
Forum: Construction Equipment
08-27-2017, 04:34 PM
|
Replies: 43
Views: 22,186
Re: Bruder 574 RC conversion weekend project!
Hi Skeeter,
I just used whatever I had laying around. It was this one:
- 4x4mm coupling: http://www.ebay.com/itm/231268270917
Later I bought these, which I would rather have used:
- 4mm...
|
Forum: Construction Equipment
08-27-2017, 02:33 PM
|
Replies: 43
Views: 22,186
Re: Bruder 574 RC conversion weekend project!
I also did a bit of cleanup work. The initial weekend project was done in a hurry, and I didn't have all the parts I wanted to use. I ordered them, though, and I got them a bit later. I've now...
|
Forum: Construction Equipment
08-27-2017, 02:00 PM
|
Replies: 43
Views: 22,186
|
Forum: Construction Equipment Tech
08-27-2017, 08:42 AM
|
Replies: 23
Views: 7,020
|
Forum: Construction Equipment
08-27-2017, 08:12 AM
|
Replies: 43
Views: 22,186
|
Forum: Construction Equipment
08-27-2017, 07:15 AM
|
Replies: 43
Views: 22,186
Re: Bruder 574 RC conversion weekend project!
Thanks, Skeeter! :-)
Congratulations on your newly acquired printer! :-)
I've also put the files up on Shapeways if there anyone not owning a 3D-printer but still wants to get the parts made:
...
|
Forum: Construction Equipment
08-09-2017, 05:56 PM
|
Replies: 43
Views: 22,186
Re: Bruder 574 RC conversion weekend project!
I see that I've left out some information:
- The aluminum axle tubes are cut to 135mm length.
- The wheel hubs (4mm axle) were bough here: http://www.ebay.com/itm/322385127356
Best regards,...
|
Forum: Construction Equipment
06-15-2017, 05:10 PM
|
Replies: 43
Views: 22,186
|
Forum: Construction Equipment
04-19-2017, 03:05 AM
|
Replies: 43
Views: 22,186
|