Forum: Metal forming & tools
03-29-2013, 07:05 PM
|
Replies: 15
Views: 5,115
Re: Straight edge cuts
1/4 cuts like butter but teeth are too wavy to prevent side bite. not good
1/2 to 3/4 blades at 18 to 24tpi work best for me
my biggest issue is precise and stable centering especially across
|
Forum: Metal forming & tools
03-29-2013, 01:21 PM
|
Replies: 15
Views: 5,115
Re: Straight edge cuts
That's what i have been doing. Then i powersand them at 90D to get the burs and lines straight. this means i must always leave at least 1 edge factory straight which results in wasted material and a...
|
Forum: Metal forming & tools
03-28-2013, 10:19 PM
|
Replies: 15
Views: 5,115
Straight edge cuts
What is the best way to get straight edge cuts in alum plates of 2-4mm thick? For instance when you want to make some body panels that actually fit together..
I have been told horizontal bandsaws...
|
Forum: Mechanical tech
03-28-2013, 08:20 PM
|
Replies: 3
Views: 2,246
Re: Trans. Gears
pinion is 32pitch on their 3 speeds.. the internal gears i couldnt tell you
their touring cars use 48p usually.
|
Forum: Construction Equipment
03-28-2013, 06:16 PM
|
Replies: 715
Views: 331,098
Re: Kenworth 850 Off Highway
beatiful! do you have a way of presets or do you have to remeasure and align the mill for each part (where you make multiples of each, like the wheels)?
|
Forum: Construction Companies & Worksites
03-28-2013, 02:02 PM
|
Replies: 1,875
Views: 971,223
|
Forum: Construction Companies & Worksites
03-28-2013, 12:25 PM
|
Replies: 1,875
Views: 971,223
|
Forum: Construction Equipment
03-27-2013, 11:49 AM
|
Replies: 104
Views: 46,604
|
Forum: Construction Companies & Worksites
03-27-2013, 07:20 AM
|
Replies: 1,875
Views: 971,223
|
Forum: General Discussion
03-26-2013, 09:10 PM
|
Replies: 11
Views: 2,280
Re: Insuring your models?
Well bikes and seadoos are actually land and water transportation devices, much like a car and follow the same regulations. not even close to being the same in terms of legal standing to a...
|
Forum: General Discussion
03-26-2013, 07:35 PM
|
Replies: 11
Views: 2,280
Re: Insuring your models?
I was always under the assumption (as told by agents when i used them) that anything you disclose falls under the HO policy. If not disclosed and added, it isn't really covered. Guns et al are...
|
Forum: Construction Equipment Tech
03-26-2013, 04:06 PM
|
Replies: 10
Views: 2,906
Re: Quick Disconects?
http://catalog.beswick.com/#HOME
same prices as those from germany... unfortunately.
although their brass nipples are cheap. just not the disconnects
|
Forum: Construction Equipment Tech
03-25-2013, 04:16 PM
|
Replies: 3
Views: 1,333
Re: Hydro filter
Neither. Top fitting is from pump and bottom fitting goes to the valve.
You can hook it anywhere before the valves since anything after the pump will have the same pressure before it reaches the...
|
Forum: Construction Equipment
03-25-2013, 04:07 PM
|
Replies: 104
Views: 46,604
|
Forum: Construction Equipment Tech
03-24-2013, 02:37 PM
|
Replies: 2
Views: 1,335
Re: in tank return hose?
Doesnt matter as far as air; its the intake that is important to always be under water. If its aerating, it isnt bled proper. With the german hydro fluid you have to stop it and let air bleed out of...
|
Forum: General Discussion
03-23-2013, 06:13 PM
|
Replies: 46
Views: 16,352
Re: MORPOWER pump & valve
I was pulling 5amps on a 20 turn motor with the leim pump... so sure, its possible! going to a 45t torquemaster cut it to 1200mah every 15 minutes (havent amp measured that yet). soo...over an hour...
|
Forum: Construction Equipment
03-23-2013, 05:40 PM
|
Replies: 202
Views: 156,319
|
Forum: Construction Equipment
03-23-2013, 05:12 PM
|
Replies: 104
Views: 46,604
|
Forum: Construction Equipment
03-22-2013, 09:42 AM
|
Replies: 104
Views: 46,604
|
Forum: Construction Companies & Worksites
03-21-2013, 03:44 AM
|
Replies: 1,875
Views: 971,223
|
Forum: Construction Equipment Tech
03-20-2013, 05:37 PM
|
Replies: 6
Views: 2,155
|
Forum: Construction Equipment
03-20-2013, 04:36 PM
|
Replies: 104
Views: 46,604
|
Forum: Construction Equipment Tech
03-20-2013, 04:27 PM
|
Replies: 6
Views: 2,155
|
Forum: Construction Equipment
03-20-2013, 03:17 PM
|
Replies: 104
Views: 46,604
|
Forum: Construction Equipment
03-20-2013, 02:38 PM
|
Replies: 104
Views: 46,604
|