Forum: Get it out of your system! HERE!
12-01-2015, 06:17 PM
|
Replies: 6
Views: 7,516
|
Forum: Construction Equipment
11-23-2015, 07:52 AM
|
Replies: 281
Views: 185,276
|
Forum: General Discussion
11-21-2015, 08:31 AM
|
Replies: 3
Views: 1,758
|
Forum: Construction Equipment Tech
11-04-2015, 06:35 AM
|
Replies: 32
Views: 7,686
|
Forum: Construction Equipment Tech
11-03-2015, 06:50 PM
|
Replies: 32
Views: 7,686
Re: Magom Brushless Pump
1) pressure relief valve ?
2) if PRV , how is it plumbed in ?
3) RPM of pump ( any reduction in to that pump ?) ?
I assume the aluminum part on the side of the pump is the tank ? The way I plumb...
|
Forum: Construction Companies & Worksites
11-01-2015, 08:05 AM
|
Replies: 2,507
Views: 964,089
|
Forum: General Discussion
10-22-2015, 01:38 PM
|
Replies: 30
Views: 7,668
Re: I sold my baby today.....
I'm not there yet , Mario . My 68 barracuda been up in the selling discussions . It sits too much . I did sell off my 69 barracuda ( 1st 1 ) that was hard. I was going to collect them up till they...
|
Forum: Construction Companies & Worksites
10-21-2015, 08:10 AM
|
Replies: 2,507
Views: 964,089
Re: Great Dane excavating co.
The lil woman wants the biggest made by bucyrus before cat aquired them . So yea a 797 electric drive . I got a rope shovel in engineering stages to load it .
|
Forum: Construction Companies & Worksites
10-20-2015, 08:59 PM
|
Replies: 2,507
Views: 964,089
|
Forum: Construction Companies & Worksites
10-18-2015, 11:27 PM
|
Replies: 2,507
Views: 964,089
Re: Great Dane excavating co.
It my tires are 60, they would be great for a haul truck . I can't even tare them up on the loader spinning in rocks . They are of latex rubber composition .
|
Forum: Construction Companies & Worksites
10-18-2015, 05:01 PM
|
Replies: 2,507
Views: 964,089
|
Forum: Get it out of your system! HERE!
10-18-2015, 08:47 AM
|
Replies: 32
Views: 16,751
|
Forum: RCP’s Aluminum Gravel Boxes and Accessories
10-17-2015, 07:42 AM
|
Replies: 129
Views: 35,988
|
Forum: East Coast Mini Truckers Club
10-17-2015, 07:39 AM
|
Replies: 21
Views: 14,554
|
Forum: Get it out of your system! HERE!
10-14-2015, 10:18 PM
|
Replies: 32
Views: 16,751
|
Forum: Highway Trucks and Trailers
10-13-2015, 07:52 AM
|
Replies: 463
Views: 248,750
Re: bigfords trucks
Typical drivers , yea fill it up , then get the trailer rockin with the body up :rolleyes: . Good demonstration of how they roll . The moisture was pretty high .
|
Forum: Construction Companies & Worksites
10-12-2015, 06:41 AM
|
Replies: 2,507
Views: 964,089
|
Forum: Construction Companies & Worksites
10-09-2015, 10:16 PM
|
Replies: 2,507
Views: 964,089
Re: Great Dane excavating co.
look for modelman's (Tom) 777 thread , he goes over the whole tire making . Or he'll see this and help you out ;) .
I know my loader tires are made from latex rubber . you'll see it again on...
|
Forum: Construction Companies & Worksites
10-09-2015, 07:41 PM
|
Replies: 2,507
Views: 964,089
Re: Great Dane excavating co.
Make your master in the printer . Clean it up smooth it if necessary . Then make a mold and cast them like Tom did . I made the negative of the tire for machining the mold , but I forget what I did...
|
Forum: Construction Companies & Worksites
10-05-2015, 12:21 PM
|
Replies: 2,507
Views: 964,089
Re: Great Dane excavating co.
304 stainless
http://i830.photobucket.com/albums/zz230/ihbuilder/E62B8648-6C87-4DC8-9191-5DF08899CBA2_zpscnrzpjwn.jpg...
|
Forum: Construction Companies & Worksites
10-03-2015, 10:16 PM
|
Replies: 2,507
Views: 964,089
Re: Great Dane excavating co.
ID grooving, I found them on McMaster . Oring groovers and snap ring groovers . You have to take them slow and a very good sense of touch , they break easy . Always use tube for your barrels. Manual...
|
Forum: General Discussion
10-03-2015, 09:54 PM
|
Replies: 7
Views: 2,335
Re: Aluminium sale near Hartford, CT?
Someone always figures it out . :rolleyes: I still need to talk to them . And I'm not sure based on the amount I need . I'm still figuring it'll be high priced . :(
|
Forum: Construction Companies & Worksites
10-03-2015, 03:53 PM
|
Replies: 2,507
Views: 964,089
Re: Great Dane excavating co.
I have no problem on 316 . But then again you need your S&F's right . Oh your doin this manually :p Looks good so far .
|
Forum: General Discussion
10-01-2015, 06:54 AM
|
Replies: 7
Views: 2,335
|
Forum: General Discussion
09-30-2015, 08:23 PM
|
Replies: 7
Views: 2,335
|