RC Truck and Construction  

Go Back   RC Truck and Construction > Search Forums
Reload this Page Search Results
Register FAQ Calendar Today's Posts Search


Showing results 1 to 17 of 17
Search took 0.00 seconds. Search: Posts Made By: jerry56
Forum: Construction Equipment 12-20-2020, 03:31 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

LOL Tgrzes things are tucked away but far from neat much better than they were though.
Thanks Egronvold I'm still getting the hang of this...
Frizzen I just have to get a mind set for stowing wire...
Forum: Construction Equipment 12-19-2020, 04:27 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

Ok with some suggestions from Frizzen I got the wiring under control... mostly

https://live.staticflickr.com/65535/50737616856_b67df372ba_z.jpg
...
Forum: Construction Equipment 12-08-2020, 04:19 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

I finally got back to the Delta loader...I'm pretty much done with it I think although it doesn't look as neat as some I've seen.... I might have to work on some type of wire management......
Forum: Construction Equipment 10-28-2020, 04:47 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

It's all good....it's not derailed... it all relates ...and I get what your saying about not being able to tap things like JB weld...makes sense.
Forum: Construction Equipment 10-27-2020, 02:22 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

I do have a slight bend in it, I'll have to see how it does when I actually start lifting stuff..
I know it says JB weld can be drilled and tapped... but in reality can it be, and is it reliable
Forum: Construction Equipment 10-27-2020, 12:47 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

I tried messing with the end points.... and will continue to play with them .. the issue is when it seats all the way down the servo horn is below the servo center causing the piano wire to bend...
Forum: Construction Equipment 10-27-2020, 10:51 AM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

Ok I got back to this a little bit.... I ran the servo cables down the inside of the arms, I just used a dremel with a little ball shaped cutter to open up a hole in each one of the arm supports so...
Forum: Construction Equipment 10-14-2020, 05:16 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

Thanks Frizzen !
Well SmallHaul mentioned it it one of the old threads from like 2009, that you needed to match the endpoints and open the deadband way up so they don't tend to fight each other and...
Forum: Construction Equipment 10-12-2020, 08:41 AM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

Sorry these are still a little blurry, my cheapie camera doesn't like to focus up close... this shows the 2mm bolt and flat washer that keep the servo horn trapped in the lift arm the bolt goes down...
Forum: Construction Equipment 10-08-2020, 09:06 AM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

I realized I need to get the bucket curl done before I finish the lift, This is a plastic toy after all and I don't want to snap the pieces on and off any more than I have to just to be on the safe...
Forum: Construction Equipment 09-30-2020, 04:29 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

I know I noticed both of those sites are down, scale4 had build threads for the D5 and the smaller wheeled skid steer. There are a ton of threads now without pictures because of photobutt... and...
Forum: Construction Equipment 09-29-2020, 05:00 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

I know right....those little 20a ESCs can be hit or miss sometimes I had one just go up in smoke one me, one worked for a couple weeks in my tonka then just quit, and a third worked then...
Forum: Construction Equipment 09-28-2020, 08:56 AM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

I thought I had pictures of the pins in place but I don't...I used coat hanger for my pins it's about 1.9mm and easy to cut. I drilled the holes at 1.7mm so it as a snug fit then super glued the the...
Forum: Construction Equipment 09-24-2020, 05:17 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

Ok .. I got the drive wheels done...ish I used the hole in the nut trick that RC Modder uses in his Bruder conversions and it seems to work pretty well. I drilled a roughly 2.5mm hole on the flat...
Forum: Construction Equipment 09-19-2020, 04:53 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

OK this is the gear box I used, I went with the 115:1 option since it seemed to be the one that has worked best for people in the past....
Forum: Construction Equipment 09-17-2020, 04:13 PM
Replies: 27
Views: 4,511
Posted By jerry56
Re: Bruder Delta loader conversion

LOL yes they do keep them together....just starting , this one might take a while since the weather here in the mid-Atlantic is cooling off I have a ton of stuff to do outside before winter gets here...
Forum: Construction Equipment 09-16-2020, 04:54 PM
Replies: 27
Views: 4,511
Posted By jerry56
Bruder Delta loader conversion

Ok I built a little dump truck but have no way to load it.... so it's time to do the obligatory Bruder Delta loader conversion..
It looks like it's been 10 plus years since the first one of these...
Showing results 1 to 17 of 17

 
Forum Jump

All times are GMT -4. The time now is 12:01 AM.

Contact Us - RC Truck and Construction - Archive - Top

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.