RC Truck and Construction  

Go Back   RC Truck and Construction > RC Tech section. > Mechanical tech

Mechanical tech This is for the mechanical parts of a model. Gear reductions, Axles, Transmissions, General drive line


Reply
 
Thread Tools Display Modes
  #1  
Old 08-12-2017, 06:10 PM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default I'm puzzled

Picked up a bargain, a high lift.The guy admitted that shifter is finicky. Brought it home, the problem is the higher gear doesn't engage, high pitch sound and nothing, lower and second ok. Took the gear box apart, seems to be ok, added grease, tested manually,works fine. Rear axle was a bit stripped, but not much, changed the parts. Same problem: upside down, all is fine shifting and engaging ok, on the floor only low and second, high slips with high pitch motor.
Any ideas?
Reply With Quote
  #2  
Old 08-12-2017, 08:23 PM
frizzen's Avatar
frizzen frizzen is offline
Big Dawg On The Bone
 
Join Date: Jan 2016
Location: indy, indiana
Posts: 2,040
frizzen is on a distinguished road
Default Re: I'm puzzled

Kinda sounds like one of the 3rd gears snapped a cross pin / hogged out a spline holding it to either top or bottom shaft.

Pull the trans case off, run it upside down in 3rd and squeeze tires on an axle to put load on it. Should be able to see which gear slips on shaft.
__________________
What do ya mean "Cars are neither Trucks or Construction"?
It's still scale, and i play fairly well with others, most of the time...
Reply With Quote
  #3  
Old 08-13-2017, 08:02 PM
bigdogrod bigdogrod is offline
Green Horn
 
Join Date: Aug 2011
Location: maryland - 20814
Posts: 264
bigdogrod is on a distinguished road
Default Re: I'm puzzled

either that or the shiftier is not throwing the gear far enough to engage, see if you can get it in manually

>that's what she said!<

Reply With Quote
  #4  
Old 08-14-2017, 08:57 AM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default Re: I'm puzzled

Thanks for coming through, on manual shifts ok, I changed the servo to a metal high torque, much better but not perfect. Just like real car, switching into third from stop, takes a lot of throttle before it takes off. Not The same as my other High lifts, but at least it moves.
Reply With Quote
  #5  
Old 08-14-2017, 10:04 AM
bigdogrod bigdogrod is offline
Green Horn
 
Join Date: Aug 2011
Location: maryland - 20814
Posts: 264
bigdogrod is on a distinguished road
Default Re: I'm puzzled

check out the servo throw, it might not be engaging enough, longer servo arm or adjust end points on radio if yours has that setting
Reply With Quote
  #6  
Old 08-14-2017, 07:07 PM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default Re: I'm puzzled

Found the problem: stripped the gearbox completely apart and discovered that one of the slip gears was on the wrong side and fully engaged, so when you tried to shift, no room to go.... All fine now.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:10 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.