RC Truck and Construction  

Go Back   RC Truck and Construction > RC Tech section. > Metal forming & tools

Metal forming & tools If it bends,twists,welds,cuts & turns metal.Post it here


Reply
 
Thread Tools Display Modes
  #1  
Old 04-12-2015, 04:42 PM
Rvjimd's Avatar
Rvjimd Rvjimd is offline
Craftsman
 
Join Date: Dec 2012
Location: Des Moines, Iowa
Posts: 884
Rvjimd is on a distinguished road
Default My New Lathe & Mill

I got a lathe about four months back and a mill a few weeks ago. I am about to get a serious start on a dozer. I have been learning how to operate both machines and have had a few little learning projects already come thru the shop.

My most recent project is making some steady rest wheels for my brother-in-law. The steady rests are for a fishing rod lathe. I also did a set if pneumatic brakes for an RC jet, and a conversion of a belt reduction drive to allow an electric motor instead of glow. Also pictured are two prototype track pads I'm thinking about trying a pinned crawler track for the NyLint dragline.






Last edited by Rvjimd; 04-12-2015 at 04:53 PM. Reason: Pics
Reply With Quote
  #2  
Old 04-20-2015, 11:43 AM
modelman modelman is offline
Craftsman
 
Join Date: Aug 2010
Location: Cullman Al.
Posts: 856
modelman is on a distinguished road
Default Re: My New Lathe & Mill

Hi jim-as a non-machinist, all I can tell you is practice, practice, practice and learn all you can. Looks like you are off to a good start. One thing I can say I learned about the tracks. The pin placement in the track pads is critical to getting the correct pitch. I would say make several track pads and assemble them and see if they have the correct pitch around the sprocket. On my shovel the pitch was different with the pads laying flat than when it was wrapped around the sprocket and I never got it exactly right. Just experiment and work it out. Good luck Tom
Reply With Quote
  #3  
Old 04-20-2015, 11:55 AM
Cooper's Avatar
Cooper Cooper is offline
Big Dawg On The Bone
 
Join Date: Oct 2013
Location: Watsontown, Pa
Posts: 2,119
Cooper is on a distinguished road
Default Re: My New Lathe & Mill

Welcome and congrats on the new toys to make toys . I also am a self taught machinist (wanna-be) . Model man is right with making just enough to see if they work. Titandigs, Paul, has a dozer thread with awesome machining skills. He was the one to tell me about track pad spacing. If they are too tight they will get clogged and spring up like a ticked-off cat. I forget what he recommended but at least a few mm between pads/shoes. I ended up re milling all of them to allow a bit more space. If I make tracks again I believe I will try and add relief holes to the pads. Good luck and once the tracks are done the rest will be a lot less repetitive work. Only time I really have track problems is when I'm not paying attention and turn sharp in loose dirt filling links then the sprocket packs it in and slips. Just like 1:1 machines you really don't want to have a lot of dirt/rocks spill into track links. And keep posting progress pics, it's always interesting to see what others find solutions for and how they go about it !!
__________________
Always wasting money, as the wife says.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote
  #4  
Old 04-20-2015, 11:57 AM
Cooper's Avatar
Cooper Cooper is offline
Big Dawg On The Bone
 
Join Date: Oct 2013
Location: Watsontown, Pa
Posts: 2,119
Cooper is on a distinguished road
Default Re: My New Lathe & Mill

And I was just referring to dozer pads, I don't have any experience with crawler/crane tracks, I don't think they are as critical.
__________________
Always wasting money, as the wife says.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote
  #5  
Old 06-22-2015, 12:27 PM
Claus H Claus H is offline
Newbie
 
Join Date: Mar 2015
Posts: 7
Claus H is on a distinguished road
Default Re: My New Lathe & Mill

Nice Work im a student of machinist , and must say nice Work . dont know if you are using a micrometer for all details ? . i have made a lot of jobs from bike parts , repair jobs , and a lot of tools . im glad to help if i can .
Attached Images
File Type: jpg WP_20150611_006.jpg (157 Bytes, 193 views)
File Type: jpg WP_20150612_001.jpg (157 Bytes, 190 views)
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:47 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.