|
|
|
|
#1
12-24-2015, 09:36 AM
|
||||
|
||||
vises
Where do you guys get the vises for the baby bench top mills ? I looked at HF and MSC , no luck . I need a good manual mill but I'm stuck with the tige for little longer and the Vise that came with it ( as Lynn warned
 ) is crap . Also out lived any more tweeking that I could doo with it .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. 
|
|
#2
12-24-2015, 09:48 AM
|
||||
|
||||
|
Re: vises
Sherline is one that I use. The other is a drill vice that I adapted to fit my small mill.
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe
|
|
#3
12-24-2015, 09:56 AM
|
|||
|
|||
|
Re: vises
Try Little Machine Shop they should have one of what you want and if they do and they and you are going to Cabin Feaver you can buy it and tell them to bring it it the show that should save you some money. Ed
Last edited by JAMMER; 12-24-2015 at 09:58 AM.
|
|
#4
12-27-2015, 06:00 PM
|
||||
|
||||
|
Re: vises
Steve, sorry to jack the thread. I sent you a PM and email through your web site but have not heard back in several days. When you get a chance, could you please send me a quick reply so I can order. Thanks. I apologize for intrusion guys, just trying to get in touch with IHBuilder.
|
|
#5
12-28-2015, 08:14 AM
|
||||
|
||||
|
Re: vises
Quote:
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#6
12-28-2015, 08:26 AM
|
||||
|
||||
|
Re: vises
Thanks guys , I'll look around at cabin fever . I really need a bridgeport size manual mill for which I got plenty of vises to fit . I've seen grizzly has a single phase clone with a DRO for not too bad a price . I'm just skeptical on quality . I'll need to make a trip to Muncy some day to look at em .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#10
12-28-2015, 03:36 PM
|
||||
|
||||
|
Re: vises
Grizzly is basically in my backyard, 15 min away, they are already gone. I would look at little machine shop, it was nice having grizzly that close as no other places around that I could sameday break something and drive to get new. Back to everything mail order
 vices are something I would spend a little $ on. Got a couple cheep mill vices at grizzly and they are not very true. The one silver 2" adjustable angle vice was not parallel to table by .05", really hard to get a square angle. I messed with it and got it parallel down to .02. If ya don't need too accurate I'll bring it to cabin fever
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
 |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
