![]() |
|
Australian Rigs & Roadtrains A place for aussies to show off their unique truck configurations. |
![]() |
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
![]()
This is where im at with my building so far.
Cheers Rhys |
#2
|
|||
|
|||
![]()
Trailers
|
#3
|
|||
|
|||
![]()
Trailers
|
#4
|
|||
|
|||
![]()
Done some work on knight hauler today.
Tanks and straps.side steps.and stone deflector. And lower running board across bottom to carry leds.. |
#5
|
|||
|
|||
![]()
Front view
|
#6
|
||||
|
||||
![]()
Hey ozy operator non of your pics work.
|
#7
|
|||
|
|||
![]()
Oh ok thanks for the heads up.
not sure why they wont work. shows them uploaded in manage attachment. Go to preview post and there not there anyone help me on this Cheers Rhys |
#8
|
||||
|
||||
![]()
Hi Ozy, Dreamweaver put this thread together and it helped me when I had got started. Hope it helps.
http://www.rctruckandconstruction.co...ead.php?t=4057
__________________
Brian |
#9
|
|||
|
|||
![]()
Thank you for the link. See how I go with it this time very helpful indeed.
Cheers Rhys |
#10
|
|||
|
|||
![]() |
#11
|
|||
|
|||
![]() |
#12
|
|||
|
|||
![]() |
#13
|
||||
|
||||
![]()
Couldn't see any pics in your 1st post till I rolled down, great job
![]() |
#14
|
|||
|
|||
![]()
Thanks chris1210 had a few issues uploading lol.
|
#15
|
|||
|
|||
![]()
Any hydraulic experts here need to pick your brains on how it works.
Going to need 2 rams 1x5 stage and 1x4 stage. so is it 1 pump and esc per ram or can I use a diverter block to send oil to the other ram if that makes sense.. any info would be great. cheers Rhys |
#16
|
||||
|
||||
![]()
Are you planning to use Scaleart hydraulic system? As I know they have long and short telescope cylinders, but you have to modify your long dump box to fit their long telescope cylinder.
|
#17
|
|||
|
|||
![]()
I think that is the way i will go they seem to be good cylinders all comes down to getting the 2 cylinders working of one pump and esc.
Plan is to have a diverter valve in the feed line running of servo to open shut valve to divert between the 2 cylinders. This is my thoughts anyway. Its how the 1.1 trailers are setup to work, use to be a pain dumping rear trailer then position 1st trailer to dump then get out of truck and pull isoltion vavle on side of 1st trailer to run that cylinder. |
#18
|
|||
|
|||
![]()
Just been on scaleart website and I must say the exchange rate to autralian dollar from euros is a killer. 1 euro=1.50 australian this could get very expensive indeed.
Wont get much change from 2000 australian dollas landed im guessing. Now how to get it past the better half ![]() |
#19
|
||||
|
||||
![]()
Yes, they're pretty expensive. You may have a look on Magomhrc for their hydraulic, valves...
|
#20
|
|||
|
|||
![]()
Thanks will have a look and see what they have to offer
Cheers Rhys |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|