![]() |
#1
|
||||
|
||||
![]()
had built this a while back - have since traded it off to a new owner...... but thought I would post the pics of its build. Along the way you will notice i tried several different methods but then found a good solution
dis-assembly - & bogies ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
#2
|
||||
|
||||
![]()
glad you posted this Chris
![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#3
|
||||
|
||||
![]()
Nice to see Chris. I'd like to see how you power the hubs.
__________________
You are an inspiration to many To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. , you will not be forgotten. R.I.P. FGD Work Hard, Play Hard! Never Forget- 343 |
#4
|
|||
|
|||
![]()
Loved that tractor its a shame you traded it.
|
#5
|
||||
|
||||
![]()
don't worry It's in good hands
![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#6
|
|||
|
|||
![]()
__________________
regards, Frank |
#7
|
||||
|
||||
![]()
Great link, Frank. He has done a great job with the conversions. I hope to get mine operating that smoothly.
Ben
__________________
You are an inspiration to many To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. , you will not be forgotten. R.I.P. FGD Work Hard, Play Hard! Never Forget- 343 |
#8
|
||||
|
||||
![]()
ben I'll post some pics tomorow night with some new parts I made for it . It's getting a foot upgrade
![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#9
|
||||
|
||||
![]()
still milling parts yet and need some different size screws
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() I'm using pretty much what Chris did , just going a little bit further with the track frame pivot point . I'm doing away with the single point pivot to the inside of the track frame which would wear over time causing the track frame to come out of alignment thus , alowing the track to come off . the 1's I'm building is similar to the real 1's not as detailed but will function the same . thanks for lookin Ben , pic of the insides ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#10
|
|||
|
|||
![]()
Looks great! The transmission seems to be very solid...
__________________
regards, Frank |
#11
|
||||
|
||||
![]()
Steve - your doin g whagt I couldn't - remaking hte track frames for better alignment..... great upgrade!
The transmission was from RC4WD - its has metal gears and a machined aluminum case - twin 55 turn motors..... the differentials came from a Duratrax Nitro Quake - see last pic..... some more pics of the original build up..... ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
#12
|
|||
|
|||
![]()
Looks great!
Ten Cells (12V).... Did I see it right? What capacity do they have?
__________________
regards, Frank |
#13
|
||||
|
||||
![]()
They are the cell pack from a dewalt 12v drill unit - They didn't work out so well though..... probably half shot to begin with (garage sale drill)
Steve - what packs od you run now?? |
#14
|
||||
|
||||
![]() Quote:
![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#15
|
||||
|
||||
![]()
I am liking these tracked tractors.
|
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|