![]() |
|
Big Boys of the road 4x4/6x6/8x8/10x10 Trucks This forum is for those multiple axle trucks and other vehicles on and off road. |
![]() |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
got an idea! a year ago. same time as the bullhead. built at same time.
started by ordering parts from all over the world. bought a frame and gearbox. had an idea it would be possible to make the six wheel drive. ![]() ![]() wondered if I could raise the gearbox so I got more ground clearance. ![]() ![]() |
#2
|
|||
|
|||
![]()
ordered two rear sections, I could cut and extend it.
![]() wanted to cut them here and there!! ![]() ![]() |
#3
|
|||
|
|||
![]()
went home to my brother in law to cut them.
![]() ![]() ![]() |
#4
|
|||
|
|||
![]()
this was my idea of how it would look
![]() ![]() ![]() also bought two frames for extension!! ![]() Last edited by krankillen; 11-13-2012 at 02:15 PM. |
#5
|
|||
|
|||
![]()
two become one! again!!
![]() ![]() ![]() ![]() |
#6
|
|||
|
|||
![]()
glued together rear truck bed!
![]() ![]() |
#7
|
|||
|
|||
![]()
now that I'm doing this. then I had no drawing! it was all in my head, the problems which arose were solved gradually.
cut the frame and welded them. ![]() ![]() ![]() |
#8
|
|||
|
|||
![]()
I was going to raise the gearbox. it started good .... but when the body was in place, then the gearbox was too high. redo, do it right! Now it starts to get complicated.
![]() angle of the drive shaft became very sharp!!!!! Last edited by krankillen; 11-13-2012 at 02:35 PM. |
#9
|
|||
|
|||
![]()
had to rout a new aluminum plate with a different angle. so I could lay down on the gearbox on the side.
![]() ![]() ![]() ![]() ![]() |
#10
|
|||
|
|||
![]()
I was going to use the original steering.
![]() servo is moved from the side, in front of the gearbox instead. Last edited by krankillen; 11-13-2012 at 02:53 PM. |
#11
|
|||
|
|||
![]()
is not so much images on the rear wheels. it will be rear-wheel steering. intend to use the original steering here. but had to remove it. I put a servo instead.
![]() ![]() |
#12
|
|||
|
|||
![]()
ordered a sound kit that would fit somewhere!!!
![]() |
#13
|
|||
|
|||
![]()
grind, grind, grind! a fifth wheel on the truck and a winch
![]() ![]() |
#14
|
|||
|
|||
![]()
Test assembly of body
![]() ![]() took away the color of the shock absorbers. ![]() |
#15
|
|||
|
|||
![]()
tested where the speakers will fit.
![]() |
#16
|
|||
|
|||
![]()
a battery would fit somewhere!!
![]() cut into the sound box, to make room for the battery. ![]() |
#17
|
|||
|
|||
![]()
tried to paint two colors on the truck, but did not get a good line on the colors
![]() ![]() ![]() |
#18
|
|||
|
|||
![]()
many cables it becomes!
![]() buy rims for the truck! use the original tires. for they go well with the car ![]() |
#19
|
|||
|
|||
![]()
transmitter was ordered! it should be used to the gearbox and two winches, as well as the fifth wheel.
![]() |
#20
|
|||
|
|||
![]()
it looks like this now! rims have not installed yet.
![]() ![]() ![]() ![]() |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|