Magom HRC metal 1/14 track loader

[Lil Giants]

Originally Posted by trucker n

Joe the one they show for sale is 900

900 what?

The numbers I see stamped on the Jung pumps is 4001, which is 0,15ml/rev, 4002 is 0,30ml/rev, 4003 is 0,45ml/rev... they go higher volume yet, but I don't know the serial #'s or values.

Anything more than 4002 - 0,30ml/rev is over kill for these little models with small bores & short strokes, especially if direct drive then 0,15ml/min would be sufficient. I think 380 - 420ml/min is the correct flow rate for these small models.

[Kausekaos]

They responded fairly quick, until next week than.

Customer message: I'm really interested in your TL14. Can i get the specs of the machine?
Height, Length, Width.
How high dose the bucket lift?

Response

Thanks for contact us and be interested in our products.
All the dimensions for the TL14 will be available next week.
Also we will make power testings.

Any doubts, questions, please do not hesitate to contact us again,

[Kausekaos]

True that is a option.

[RCP57]

Just let the moths out of your wallet and order one up.

[Kausekaos]

I really thing I'm going too honestly.

[Supermario]

Just saw some new pics of this loader. Is it just me? Looking from this angle this thing has a very very low ground clearance is 15mm enough?

[RCP57]

Originally Posted by Supermario

Just saw some new pics of this loader. Is it just me? Looking from this angle this thing has a very very low ground clearance is 15mm enough?

Great for ground rubber on a cement floor maybe. I understand why they probably did this but that's not much ground clearance. It will be constantly dragging it's belly that's for sure.

[Kausekaos]

Never realized that low ground clearance. It looks good painted though. There's more pictures on their Facebook page.

[trucker n]

Just purchased one will see what it's like when I get it

[Mikem]

But doesn't the bucket move and level the dirt so the ground clearance wouldn't matter ? Just a question . I looked at there site Sunday and its out of stock I'll go look again

[trucker n]

Yeah I saw out of stock I emailed them and got reply this morning that all was back in stock I also noticed they sell the Jung pump witch I wanted but they said it won't fit in this machine I also got the sound for it

[Rakthi]

There are some pics of it being assembled on the Modell-Baustelle.de forum

Here is the link:
http://www.modell-baustelle.de/index...&threadID=8638

[Rimrock]

Originally Posted by trucker n

Yeah I saw out of stock I emailed them and got reply this morning that all was back in stock I also noticed they sell the Jung pump witch I wanted but they said it won't fit in this machine I also got the sound for it

Magom got the Jung pump, but keep in mind that the motor/tank/ is Magom's own set-up (cheap) and will not perform as good as the same Jung pump delivered with Premacon or Fumotec set-up...This Jung pump is prepared for fare larger machines than this loader and would probably be needed to be tuned down to 10-20% of max performance, if at all manage to fit it in the machine

[Lil Giants]

Originally Posted by Rimrock

Magom got the Jung pump, but keep in mind that the motor/tank/ is Magom's own set-up (cheap) and will not perform as good as the same Jung pump delivered with Premacon or Fumotec set-up...This Jung pump is prepared for fare larger machines than this loader and would probably be needed to be tuned down to 10-20% of max performance, if at all manage to fit it in the machine

Depends on what Jung pump they're using, do you know?

[Rimrock]

Originally Posted by Lil Giants

Depends on what Jung pump they're using, do you know?

It's the HR-7 / 4003. Magom does not use a reduction transmission, to keep cost down, installed a oversized motor in order to reduce the rpm. But I personally think it runs higher at full speed than the recommended 3-4000 max rpm for the pump. Too small tank (50-100 ml, vs Premacon 500 ml), no good cooling of the oil, which then more quickly gets hot and start foaming. Magom got much nice suff now, as the tracked loader, but they still got some way to go concerning their pumps, IMO.

[Mikem]

So do you guys think this is a good beginner shovel . I like the price . Is there someone else's pump to use?

[trucker n]

I think is a good starter them maybe later upgrade to leimbach pump and valves

[Northern Farmer]

I personally would go with the Carson LR634 but to each their own

[Mikem]

But will a liembach pump and valves fit ? Can the motor as it is be slowed down ?

[Rimrock]

Originally Posted by Mikem

But will a liembach pump and valves fit ? Can the motor as it is be slowed down ?

I guess there are dimension sketches of both brand's pumps available at their web pages...look a bit around..