|
Construction News New kits & accessories offered in the world wide marketplace |
|
Thread Tools | Display Modes |
#21
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
Just let the moths out of your wallet and order one up.
|
#22
|
|||
|
|||
Re: Magom HRC metal 1/14 track loader
I really thing I'm going too honestly.
__________________
Not trolling anymore... To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#23
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
Just saw some new pics of this loader. Is it just me? Looking from this angle this thing has a very very low ground clearance is 15mm enough?
|
#24
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
Great for ground rubber on a cement floor maybe. I understand why they probably did this but that's not much ground clearance. It will be constantly dragging it's belly that's for sure.
|
#25
|
|||
|
|||
Re: Magom HRC metal 1/14 track loader
Never realized that low ground clearance. It looks good painted though. There's more pictures on their Facebook page.
__________________
Not trolling anymore... To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#26
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
Just purchased one will see what it's like when I get it
|
#27
|
|||
|
|||
Re: Magom HRC metal 1/14 track loader
But doesn't the bucket move and level the dirt so the ground clearance wouldn't matter ? Just a question . I looked at there site Sunday and its out of stock I'll go look again
|
#28
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
Yeah I saw out of stock I emailed them and got reply this morning that all was back in stock I also noticed they sell the Jung pump witch I wanted but they said it won't fit in this machine I also got the sound for it
|
#29
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
There are some pics of it being assembled on the Modell-Baustelle.de forum
Here is the link: http://www.modell-baustelle.de/index...&threadID=8638
__________________
Cheers, Stephan (Rakthi is the one in the avatar) |
#30
|
|||
|
|||
Re: Magom HRC metal 1/14 track loader
Magom got the Jung pump, but keep in mind that the motor/tank/ is Magom's own set-up (cheap) and will not perform as good as the same Jung pump delivered with Premacon or Fumotec set-up...This Jung pump is prepared for fare larger machines than this loader and would probably be needed to be tuned down to 10-20% of max performance, if at all manage to fit it in the machine
|
#31
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
Quote:
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#32
|
|||
|
|||
Re: Magom HRC metal 1/14 track loader
That is a good question. I own a magom track loader,1/16 bruder conversion and it just makes it into the dump truck. Being that the metal version is 1/14 scale it should be high enough.
|
#33
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
Joe the one they show for sale is 900
|
#34
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
900 what?
The numbers I see stamped on the Jung pumps is 4001, which is 0,15ml/rev, 4002 is 0,30ml/rev, 4003 is 0,45ml/rev... they go higher volume yet, but I don't know the serial #'s or values. Anything more than 4002 - 0,30ml/rev is over kill for these little models with small bores & short strokes, especially if direct drive then 0,15ml/min would be sufficient. I think 380 - 420ml/min is the correct flow rate for these small models.
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#35
|
|||
|
|||
Re: Magom HRC metal 1/14 track loader
It's the HR-7 / 4003. Magom does not use a reduction transmission, to keep cost down, installed a oversized motor in order to reduce the rpm. But I personally think it runs higher at full speed than the recommended 3-4000 max rpm for the pump. Too small tank (50-100 ml, vs Premacon 500 ml), no good cooling of the oil, which then more quickly gets hot and start foaming. Magom got much nice suff now, as the tracked loader, but they still got some way to go concerning their pumps, IMO.
Last edited by Rimrock; 02-10-2016 at 04:23 PM. |
#36
|
|||
|
|||
Re: Magom HRC metal 1/14 track loader
So do you guys think this is a good beginner shovel . I like the price . Is there someone else's pump to use?
|
#37
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
I think is a good starter them maybe later upgrade to leimbach pump and valves
|
#38
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
I personally would go with the Carson LR634 but to each their own
|
#39
|
||||
|
||||
Re: Magom HRC metal 1/14 track loader
Quote:
I started with that pump in my Fumotec 490, it was like operating a pneumatic system, too fast - kinda springy movements. I put that pump in my JD850 & with it's much larger cyl bores, it's perfect speed, especially on the twin 18's lifting the boom. I doubt Magom pays any attention to this forum, so my words are meaningless...
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#40
|
|||
|
|||
Re: Magom HRC metal 1/14 track loader
But will a liembach pump and valves fit ? Can the motor as it is be slowed down ?
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|