|
Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
|
Thread Tools | Display Modes |
#41
|
|||
|
|||
Re: cat D6T 6 way blade
Hi Tom Seilbagger here on the form did a D8 with cables. Ed
|
#42
|
|||
|
|||
Re: cat D6T 6 way blade
http://www.rctruckandconstruction.co...662339&thumb=1 Seilbagger Hi Tom Seilbagger did a D 8 with cable lift blade. Ed
|
#43
|
||||
|
||||
Re: cat D6T 6 way blade
thanks fellers. here's a few more
Oh, duh need 2 per cylinder making 6 so need 12 and nice to have a decent vice on this toy
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#44
|
||||
|
||||
Re: cat D6T 6 way blade
Steve it's going good over there..........Carry on Please
|
#45
|
||||
|
||||
Re: cat D6T 6 way blade
Looking good Steve!
Any plans to make a wider wishbone to move tracks away from body?
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#46
|
||||
|
||||
Re: cat D6T 6 way blade
Joe, the track frames will stay where they are . On the real machine the track pads are off set on the chains . I plan to mill new tracks in the future. They're designed and programmed . It's just a matter of devoting the mill time .
Finally got all the cylinder parts done well I still need to mill the tear drop on the pins yet . Also need to move the angle cylinder bosses out on the blade .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#47
|
|||
|
|||
Re: cat D6T 6 way blade
Looks like you have put a lot of hours in this model steve, but it will be well worth it. Great job.
|
#48
|
||||
|
||||
Re: cat D6T 6 way blade
How much offset?
Lmk when you decide to do the links, I might be interested in helping you offset your costs by getting a set.
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#49
|
||||
|
||||
Re: cat D6T 6 way blade
Move the pad out by 1 hole on the link . I could do it with these ,I just need to drill 2 more holes per pad . I'll keep you in mind .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#50
|
||||
|
||||
Re: cat D6T 6 way blade
few more
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#51
|
||||
|
||||
Re: cat D6T 6 way blade
Steve,
Your gonna need to train a aux operator to manage all that stuff! Jim |
#52
|
||||
|
||||
Re: cat D6T 6 way blade
Tell me about it. Jim I have to start training the kids
plumbed cept for sleeves for the 3mm fittings
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#53
|
||||
|
||||
Re: cat D6T 6 way blade
Dang!! Lots of hoses n fittings!! Looks pretty cool!!!
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#54
|
|||
|
|||
Re: cat D6T 6 way blade
Steve-the dozer is looking good. Seems like a complicated build to me but probably not for a machinist like you. Nice work!
|
#55
|
|||
|
|||
Re: cat D6T 6 way blade
I have a quick question for you! When soldering on the rams does that effect the internals?? I was told if u heat them up they have to be re-honned?
|
#56
|
||||
|
||||
Re: cat D6T 6 way blade
hone after soldering . the gland end on mine are threaded
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#57
|
||||
|
||||
Re: cat D6T 6 way blade
How the heck to take a video while operating a 6 way blade dozer No I cant afford 1 of them gopro thingys y'all got . Yea the 3 thing I was dooing while running between lathe and mill yesterday , gettin this running proper and leak free . I had a chance to fill in the hole that always seems to appear at the man door to the shop after awhile . Now for the finishing touches and paint
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#58
|
||||
|
||||
Re: cat D6T 6 way blade
New hood ,from mill machine to finished painted part and grill . All the black painted except the blade (need sandblasting ) . Gps poles made . And a comparison pic of the td40 next to the 6
Took me 3 tries to post this the Internet is so screwed up . We paid for faster and better upgrade and its werse then to try to get an actual person to talk to , takes more time then my patience can handle . Well , phone werks
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#59
|
||||
|
||||
Re: cat D6T 6 way blade
Wow that's impressive! Hard to see an Izzy dozer in there.
|
#60
|
||||
|
||||
Re: cat D6T 6 way blade
The Dresser looks like it's in a different scale! Beautiful work on the D6
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|