RC Truck and Construction  

Go Back   RC Truck and Construction > RC Truck's Kings of the Road > Highway Trucks and Trailers

Highway Trucks and Trailers On road trucks and trailers single and twin axle trucks.


Reply
 
Thread Tools Display Modes
  #21  
Old 08-11-2016, 02:07 PM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default Re: WRECKER

Brandon, the actuators are:L 12-30-210-6-R
Reply With Quote
  #22  
Old 08-11-2016, 03:18 PM
Northern Farmer's Avatar
Northern Farmer Northern Farmer is offline
Big Dawg On The Bone
 
Join Date: Jul 2015
Location: Montreal QC
Posts: 1,513
Northern Farmer is on a distinguished road
Default Re: WRECKER

Quote:
Originally Posted by kaptain Jack View Post
A question for electronics savvy: Did a test drive today with all the functions connected, Firgellis are working fine, however, when connecting winch motor with its own speed control and its own battery,to the RX, the truck goes full throttle....
Could it be electrical interference ? Jack have you tried moving the wires around that power the winch while it's working to see if it effects anything.
Reply With Quote
  #23  
Old 08-12-2016, 04:21 AM
gismow's Avatar
gismow gismow is offline
Green Horn
 
Join Date: May 2014
Location: Dortmund, Germany
Posts: 265
gismow is on a distinguished road
Default Re: WRECKER

Hi do you have a schematic drawing of the cabeling or some photos to get an overview what is setup at the moment?
__________________
Greetinx
Peter
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote
  #24  
Old 08-12-2016, 07:45 AM
frizzen's Avatar
frizzen frizzen is offline
Big Dawg On The Bone
 
Join Date: Jan 2016
Location: indy, indiana
Posts: 2,040
frizzen is on a distinguished road
Default Re: WRECKER

When you run 2 esc, you are supposed to pull the red wire out of the RX plug on one esc so the 2 bec in them don't fight over trying to power the rx. Lift the tab and slide it out and just heatshrink or tape it out of the way. It'll smoke the bec inside one of the esc fairly quickly if you don't.

It gets even more important when running 2 isolated battery packs, or external bec.

http://www.rccrawler.com/forum/elect...otors-etc.html

If that doesn't get it, post a pic or wiring diagram of your setup.

Last edited by frizzen; 08-12-2016 at 07:55 AM. Reason: Add link
Reply With Quote
  #25  
Old 08-12-2016, 08:37 AM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default Re: WRECKER

Great advice Frizzen, I'll look into it. Mean while, I changed the esc, from chinese to RC4WD and it seems to work fine.
here is the picture of aftermarket esc

I'll try again with aftermarket later on today and will pull the red wire out, will post the results.
Thanks to everyone who replied to my question.

Last edited by kaptain Jack; 08-12-2016 at 08:45 AM.
Reply With Quote
  #26  
Old 08-19-2016, 09:48 AM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default Re: WRECKER

Disconnecting red wire from rx connector worked great!! But now, new question: I have attached retracting legs to the rear of the truck (Tamiya, the ones that go on the trailer), I have only one channel left on the radio, up and down switch I thought of using it to deploy and retract legs. I soldered the motor wires to the the motor of the servo and it works,however, the travel distance is to short !!! Disconnecting the stopper on the servo makes it rotate continuously non stop. Any suggestions on how to deploy the the legs?
Thanks
Reply With Quote
  #27  
Old 08-20-2016, 01:38 AM
Cossett's Avatar
Cossett Cossett is offline
On Leave
 
Join Date: Aug 2010
Location: Sydney Aus
Posts: 1,383
Cossett is a jewel in the roughCossett is a jewel in the roughCossett is a jewel in the roughCossett is a jewel in the rough
Default Re: WRECKER

Depending on what radio you have you could run another RX and have it in a different model memory like others do when you run out of channels or just but a new radio with more channels...

Cheers Tracy
__________________
RIP FreddyGearDrive 2-12-59/12-19-11
Love my Kenworths

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote
  #28  
Old 08-20-2016, 09:31 PM
frizzen's Avatar
frizzen frizzen is offline
Big Dawg On The Bone
 
Join Date: Jan 2016
Location: indy, indiana
Posts: 2,040
frizzen is on a distinguished road
Default Re: WRECKER

Glad to hear pulling the wire got the esc working!

Does your radio have 'epa' or end point adjustment on that channel? If so, you can start dialing the endpoints further away from center until you're happy.
If it doesn't, you might be able to fit a 'servo stretcher' in the model that wires between the rx and servo to control endpoints. Its a set of pots and a circuit card that let you configure center and each end stop independantly, so they take some time to fiddle with.
Reply With Quote
  #29  
Old 08-21-2016, 11:16 AM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default Re: WRECKER

Thanks Tracy. Thanks Frizzen, I'll see what my radio is capable of doing.
Jack
Reply With Quote
  #30  
Old 08-23-2016, 08:20 AM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default Re: WRECKER



Reply With Quote
  #31  
Old 08-23-2016, 10:09 PM
spudd spudd is offline
CEO of bend over motors."WE DRIVE IT HOME!"
 
Join Date: Dec 2010
Location: milaca minnesota
Posts: 1,032
spudd has a spectacular aura aboutspudd has a spectacular aura about
Default Re: WRECKER

great idea on the rear down riggers
__________________
Specializing in VW beetle water pumps!

RIP FREDDYGEARDRIVE
Reply With Quote
  #32  
Old 09-17-2016, 10:21 AM
dabears's Avatar
dabears dabears is offline
Dairyland trucker's right hand man.
 
Join Date: Mar 2012
Location: Chicago, IL
Posts: 2,005
dabears is on a distinguished road
Default Re: WRECKER

Starting to look like the 50 Ton I used to drive before I moved back to Illinois. Great start!
__________________
Hi my name is Aaron.... And i'm a truckaholic!
Reply With Quote
  #33  
Old 09-17-2016, 08:43 PM
PaulNZ's Avatar
PaulNZ PaulNZ is offline
Green Horn
 
Join Date: Jun 2014
Posts: 198
PaulNZ is on a distinguished road
Default Re: WRECKER

Looking good Capt!
__________________
Cheers
Paul
PKD Scale Engineering

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote
  #34  
Old 10-21-2016, 01:39 PM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default Re: WRECKER

Did some more work on the truck
Reply With Quote
  #35  
Old 10-21-2016, 02:17 PM
egronvold's Avatar
egronvold egronvold is offline
Big Dawg On The Bone
 
Join Date: Dec 2010
Location: Conshohocken, PA
Posts: 1,445
egronvold is on a distinguished road
Default Re: WRECKER

Beautiful work!
__________________
Emil G | MFZ Blocher Fendt 926 | RC4WD Volvo EC480 excavator | Carson LR 634 | Kenworth 6x6 hauler | Kenworth 6x6 dtrk
My channel:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Construction site on Facebook:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Pictures on Instagram:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote
  #36  
Old 10-22-2016, 12:15 AM
Kaf343's Avatar
Kaf343 Kaf343 is offline
Journeyman
 
Join Date: Feb 2012
Location: West Milford, NJ
Posts: 728
Kaf343 is an unknown quantity at this point
Default Re: WRECKER

Great work so far, Looking forward to more pics and updates.
Reply With Quote
  #37  
Old 11-18-2016, 08:54 AM
kaptain Jack's Avatar
kaptain Jack kaptain Jack is offline
Journeyman
 
Join Date: Jan 2012
Location: Toronto Canada
Posts: 616
kaptain Jack is on a distinguished road
Default Re: WRECKER

Getting close to finish line
Reply With Quote
  #38  
Old 11-20-2016, 10:07 AM
pontiacmann pontiacmann is offline
Newbie
 
Join Date: Apr 2011
Posts: 38
pontiacmann is on a distinguished road
Default Re: WRECKER

very nice work
Reply With Quote
  #39  
Old 11-20-2016, 10:28 AM
scottyk scottyk is offline
Newbie
 
Join Date: Jun 2013
Posts: 112
scottyk is on a distinguished road
Default Re: WRECKER

That is awesome! Doing great man
Reply With Quote
  #40  
Old 11-20-2016, 07:07 PM
1985 kenworth's Avatar
1985 kenworth 1985 kenworth is offline
Big Dawg On The Bone
 
Join Date: Sep 2011
Location: brampton,ontario,canada
Posts: 1,845
1985 kenworth is on a distinguished road
Default Re: WRECKER

wow jack looks fantastic..let me know where i can pick it up when its finished
__________________
owner/operator.."got to operate to own"
dwayne
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:28 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.