RC Truck and Construction  

Go Back   RC Truck and Construction > RC Tech section. > Electronics tech

Electronics tech Anything to do with the electronics in a model. Lights, Radio, ESC, Servo, Basic electrical.


Reply
 
Thread Tools Display Modes
  #1  
Old 09-01-2017, 01:28 AM
jffhrvstr jffhrvstr is offline
Newbie
 
Join Date: Aug 2010
Location: Utah
Posts: 64
jffhrvstr is on a distinguished road
Default Sevronaut S20 ECS issue

I bought a Sevronaut S20 ESC a couple of years ago and finally decided to install my in my CAT 740. I followed the directions and set the voltage to 12V but it doesn't work, it doesn't send any power to the motor. When I plug in my battery I have a steady green light that turns on and after a while it is a little warm when I pick it up but other than that it doesn't work. I searched different forums but didn't find anything answers. I am using a Spektrum DXe transmitter and when I disconnect the S20 from the channel I have it in and put another servo on the same channel the servo works fine. Have any of you guys that run the S20 had this issue? Does anyone have any thing I can try to get this to work?

Thanks

Jeff

Last edited by jffhrvstr; 09-01-2017 at 01:58 AM.
Reply With Quote
  #2  
Old 09-01-2017, 02:11 AM
Rimrock Rimrock is offline
Wannabe
 
Join Date: Jul 2013
Location: Western NO
Posts: 355
Rimrock is on a distinguished road
Default Re: Sevronaut S20 ECS issue

The ESC needs 2 channels, there is a blue and a white/transperant plugg. One usually hook the up to the 2 channels on the left hand stick. This ESC has 'cruise control', so it don't quite react at first as one expect from a standard ESC. Throttle stick pulled all the way back, left/right to switch between forward/reverse. But it all should be explained in the manuel. You might also find some instructions on youtube. Very popular in Europe.
__________________
Soyland Industrier
Reply With Quote
  #3  
Old 09-01-2017, 12:54 PM
jffhrvstr jffhrvstr is offline
Newbie
 
Join Date: Aug 2010
Location: Utah
Posts: 64
jffhrvstr is on a distinguished road
Default Re: Sevronaut S20 ECS issue

Thank you for the help.

Unfortunately I don't have a blue and white/transperant plug. My S20 has the red/black wires for the battery, the blue/yellow wire to go to the motor and 4 black jumpers to set voltage and it came with an extra plug for the brake and reverse light. I don't believe that my S20 has cruise control? I took these pictures of everything my ESC came with.

The directions say, Step 1: Plug in the S20 to the receiver, Step 2: Connect the brake/reverse lights with the supplied servo plug, Step 3: Choose the battery voltage, Step 4: Connect blue/yellow wires to the motor, Step 5: Turn on transmitter and then plug in the battery, Step 6: Move the transmitter stick slowly to check the motor is turning in the right direction. Step 7: Connect the sound module to the ESC. Step 8: That's it.

[IMG][/IMG]


You wouldn't happen to have any other suggestions on how to make this ESC work?

Last edited by jffhrvstr; 09-01-2017 at 01:01 PM.
Reply With Quote
  #4  
Old 09-01-2017, 01:11 PM
Rimrock Rimrock is offline
Wannabe
 
Join Date: Jul 2013
Location: Western NO
Posts: 355
Rimrock is on a distinguished road
Default Re: Sevronaut S20 ECS issue

Sorry, I was thinking of the M20. The S20 is more simple to set up. Could you test it with another brand of radio & receiver?
__________________
Soyland Industrier
Reply With Quote
  #5  
Old 09-01-2017, 02:41 PM
jffhrvstr jffhrvstr is offline
Newbie
 
Join Date: Aug 2010
Location: Utah
Posts: 64
jffhrvstr is on a distinguished road
Default Re: Sevronaut S20 ECS issue

I'll try that, thanks again for the help. I thought this was going to be a simple plug and play, but it doesn't want to cooperate! LOL
Reply With Quote
  #6  
Old 09-01-2017, 03:05 PM
Actros4160's Avatar
Actros4160 Actros4160 is offline
Newbie
 
Join Date: Aug 2013
Location: Columbus, GA
Posts: 127
Actros4160 is on a distinguished road
Default Re: Sevronaut S20 ECS issue

The S20 is pretty simple, I have one on my own and used it. Is your BEC working for the 5Volt receiver supply? Measure if you have 5volt on the plug which plugs in to the receiver but careful not touch them together then the BEC is toast.
You can check that with a servo on a different channel input and see if the servo is moving if you don't feel to test that with a voltmeter.
Do have a instruction for it? If not I can send you one.

Bernd
Reply With Quote
  #7  
Old 09-01-2017, 04:23 PM
frizzen's Avatar
frizzen frizzen is offline
Big Dawg On The Bone
 
Join Date: Jan 2016
Location: indy, indiana
Posts: 2,040
frizzen is on a distinguished road
Default Re: Sevronaut S20 ECS issue

Check your jumpers. Looks like pic is set with 4 jumpers as normal reverse nimh lipo?
Should be something more like 3 jumpers normal, nimh, 7.2

Make sure rx connection isn't flipped over. Signal is yellow
__________________
What do ya mean "Cars are neither Trucks or Construction"?
It's still scale, and i play fairly well with others, most of the time...

Last edited by frizzen; 09-01-2017 at 04:27 PM.
Reply With Quote
  #8  
Old 09-02-2017, 02:19 AM
egronvold's Avatar
egronvold egronvold is offline
Big Dawg On The Bone
 
Join Date: Dec 2010
Location: Conshohocken, PA
Posts: 1,445
egronvold is on a distinguished road
Default Re: Sevronaut S20 ECS issue

Are you sure it's connected to the motor correctly?
__________________
Emil G | MFZ Blocher Fendt 926 | RC4WD Volvo EC480 excavator | Carson LR 634 | Kenworth 6x6 hauler | Kenworth 6x6 dtrk
My channel:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Construction site on Facebook:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Pictures on Instagram:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:28 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.