|
Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
|
Thread Tools | Display Modes |
#41
|
||||
|
||||
Re: D9R and 463 pull scraper
nice
|
#42
|
||||
|
||||
Re: D9R and 463 pull scraper
Nice to see you back on the build joe...You havent made any new vids lately...Isnt it about time ? lol..
I was over at the german construction forum that Gabreil has his D11 on and am a member there too ..I sent him a message about this place as well and hope he signs up .. |
#43
|
||||
|
||||
Re: D9R and 463 pull scraper
Thanks guys.
Lou, I figured everyone is about tired of seeing the dozer just push some dirt around. I seen that he signed up the other day, under a new name. Should have some pics in a day or two of some new junk.
__________________
Joe |
#44
|
|||
|
|||
Re: D9R and 463 pull scraper
nmbxnjjjjjjjmccccccccccccccccccccccccccxxxxxxxnnnn nnnnnnnnnnnnnnnnnnnnnnnnbbnmmmggggggggggggggbbbbbb bbb
Oh! Sorry...That was my jaw flopped on the keypad. I'm new here, and only beginning to see a whole new world of crazy cool stuff. That is outstanding work! I'm kinda stunned... RC racing has never really appealed to me, but heavy equipment? I know I don't have to tell you guys about that. RC Heavy equipment? I mean HEAVY rc heavy equipment...Words fail. Dan |
#45
|
|||
|
|||
Re: D9R and 463 pull scraper
I can't wait to see more pics and video's Joe the back trans plates and draw bar looks awsome !!!! great detail and awsome workmanship
|
#46
|
||||
|
||||
Re: D9R and 463 pull scraper
Thanks Dan and Henry.
Finally finished the drawbar and tranny detail.
__________________
Joe |
#47
|
||||
|
||||
Re: D9R and 463 pull scraper
Awesome Dozer Joe!
__________________
Scott "No load is too Small" |
#48
|
||||
|
||||
Re: D9R and 463 pull scraper
Nice SCRAPER Joe. Very impressive. I really like the older scrapers.
__________________
FabOne NW Ohio |
#49
|
||||
|
||||
Re: D9R and 463 pull scraper
Right On Joe
Your CAT is great, can't wait to see it pulling. greg |
#50
|
||||
|
||||
Re: D9R and 463 pull scraper
Thank you guys ,hope to have some pics on the scraper pretty quick.
__________________
Joe |
#51
|
|||
|
|||
Re: D9R and 463 pull scraper
Joe-the rear detail looks great! That drawbar should handle lot's of pull power on the scraper!
|
#52
|
|||
|
|||
Re: D9R and 463 pull scraper
pan pics pan pics pan pics PLEASE lol maybe a moc up shot with the 9???? please
__________________
I built this thing and have it working now what do I do with it? Last edited by td9clyde; 09-01-2010 at 10:01 PM. |
#53
|
||||
|
||||
Re: D9R and 463 pull scraper
Maybe this weekend, maybe if I get a little farther along. I am getting close though.
__________________
Joe |
#54
|
||||
|
||||
Re: D9R and 463 pull scraper
Joe, i, for one never get tired of seeing anything you build. Can't wait to see the pans
__________________
Giving up is not an option!!! Rob |
#55
|
||||
|
||||
Re: D9R and 463 pull scraper
Joe, I love this build. You guys building these Cat dozers make me wish I had the same level of skills. I'd build my own, if I could. Seems to me the hardest thing is to try and locate some good drawings. What do you work from, when you scale down and machine the parts? Blueprints, or service/part manuals? It looks so excat and perfect. Beautiful. Can't wait to see the scraper done too.
__________________
Nathan |
#56
|
||||
|
||||
Re: D9R and 463 pull scraper
Thanks guys. Nathan, I went on Cat site and downloaded the brochure on the D9R and blew it up to 1/10 scale and downloaded a whole bunch of pics off the net and went to building. Had a hard time trying to find the pics I needed for the scraper's rearend so I more or less faked it. I do most of my building by eye, which is steadly becoming a problem. This is the first time I ever attemped anything like this so it has been a learning experience from the word go.
__________________
Joe |
#57
|
|||
|
|||
Re: D9R and 463 pull scraper
Hi Joe...Thanks for the note over on U-tube..Yes the motors are very silent..Now if I could just find a winch motor that is as silent insead of that noisey thing that is in there now..
I did get a guy to haul in 2 loads of yellow clay ( 20 yards plus ) so now I have better stuff to push around and it is just outside my shop..Been bus building a locomotive for a public display so haven't had much time to play around...Maybe tomorrow I can get a photo or two.. The D9 and scraper are awsome...Love to see it load some dirt.. Jerry |
#58
|
||||
|
||||
Re: D9R and 463 pull scraper
nice machines
|
#59
|
||||
|
||||
Re: D9R and 463 pull scraper
Thanks Jerry and Ace. Glad to here you have your own dirt pile to play in Jerry, there's nothing like going and just hogging some material around with the miniature equipment.
Well I had said that I might have some pics up this weekend, however I had a semi major malfunction. I was just fixin to put a final coat of paint on the neck of the scraper and broke the soldier joint on the top of the neck that was a hinge to open the neck up to hide hydraulics in when I was going to make the scraper a self contained unit. When it broke that little part of the joint I decided to tare it completely off and weld it solid to the rest of the neck. Because I had done away with the idea of hiding the components in there anyway. So needless to say all that grinding and welding messed up a bunch off the neck paint so it set me back. But I think it looks better now anyway. I should have never trust my soldiering skills in the first place , not a strong suit of mine. lol
__________________
Joe Last edited by dirtpusher9; 09-05-2010 at 10:20 PM. |
#60
|
|||
|
|||
Re: D9R and 463 pull scraper
well i would look at it like this better now than later ........at least i know when your done it will look good and you will let us have a peek lol
__________________
I built this thing and have it working now what do I do with it? |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|