![]() |
#61
|
||||
|
||||
![]()
do these look beefy enough ?
![]() ![]() I've been working on these here and there . get a free min or to when the mill not busy ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#62
|
||||
|
||||
![]()
Look's great Steve, Keep it up
![]() ![]() ![]() ![]() ![]() ![]() Cheer's, Neil. |
#63
|
||||
|
||||
![]()
So you're going with a motor /trans combo?
What the diff ratio gonna be?
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#64
|
||||
|
||||
![]() Quote:
![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#65
|
|||
|
|||
![]()
Lookin good steve...
__________________
LARRY,the doggy dish dealer |
#66
|
||||
|
||||
![]()
You the man Steve!! that baby will be stout now. Great work as usual.
__________________
Joe |
#67
|
||||
|
||||
![]() Quote:
![]() ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#68
|
|||
|
|||
![]()
What sort of differential are you planning on using in this beaut Steve? I've been spending a lot of time on a design for a very small LSD for my loader build, but am thinking are they actually needed? With the weight these scale loaders end up, do they actually lift a wheel with open diff's? Sorry, just picking your brain here
![]() Cheers Glenn |
#69
|
||||
|
||||
![]()
" do they actually lift a wheel with open diff's "
![]() I took some time this weekend for myself ![]() ![]() ![]() ![]() ![]() ![]() ![]() rear axle assm. ![]() front and rear axle assm. ![]() carrier and axles ![]() ![]() ![]() pivot assm. and parts ![]() ![]() ![]() steel sleeve over alum. for better wear protection ![]() thanks for lookin
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#70
|
||||
|
||||
![]()
Steve That a stout looking set of axles. How many scoops will this machine take to load the Mack.
Rob |
#71
|
|||
|
|||
![]()
Thanks Steve, yep, I'm using savage diff's too
![]() Very nice looking axles! |
#72
|
||||
|
||||
![]()
prob. 6 heaped ,I know 1 heaped will load my little 10 wheeler and 1.5 brian in PA 's tri-axle
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#73
|
||||
|
||||
![]()
Wow, Steve. The axles are incredible. Beautifully machined scale replicas. I drool everytime I see something like this. CNC is amazing.
__________________
Nathan |
#74
|
||||
|
||||
![]() Quote:
![]() I wonder where that picture is? ![]() Cheer's, Neil. |
#75
|
||||
|
||||
![]()
thanks Nate , CNC is cool but can cost you in the back pocket quick
![]() yea there a big 1 Neil , I use to get loaded by a 992 with a spade nose in an old coal pit where they were crushing the lime stone over burden . 1 corner of the bucket 12ton for my lil 12' box . was something to see a tire higher then my cab ![]() fixed my wheel jig ![]() ![]() ![]() 10" face mill that came with the machine heavy as heck so you set it on the table and bring the spindle down to it
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#76
|
||||
|
||||
![]()
Wow! Great job on these axles! As we said before, CNC is a thing, the man behind is another one
![]()
__________________
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#77
|
||||
|
||||
![]()
thanks B-train
I'm testing pic quality see what you guys think ![]() Old ![]() new ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#78
|
|||
|
|||
![]()
Steve that is coming along nicely sense the last time I saw it. Ed
|
#79
|
||||
|
||||
![]()
wowza! great work!
![]()
__________________
"If you build it, they will come" East Coast Mini Truckers To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#80
|
||||
|
||||
![]()
I guess that program I told you about worked.
|
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|