|
Big Boys of the road 4x4/6x6/8x8/10x10 Trucks This forum is for those multiple axle trucks and other vehicles on and off road. |
|
Thread Tools | Display Modes |
#101
|
||||
|
||||
Re: More than just a thought ...
Yes.
|
#102
|
||||
|
||||
Re: More than just a thought ...
Great idea!
|
#103
|
||||
|
||||
Re: More than just a thought ...
That little detail didn't get past me either Might be where your tire squat is coming from?? Rotary table can't be too light! Might need some tire filling to combat the squatting.
__________________
LYNN |
#104
|
||||
|
||||
Re: More than just a thought ...
I figure that table is around 10 to 15 lbs.
But the full length 3/16 plate easn't light either. |
#105
|
||||
|
||||
Re: More than just a thought ...
Here's how I took care of those tires on my excavator dolly:
http://www.rctruckandconstruction.co...8&postcount=97 |
#106
|
||||
|
||||
Re: More than just a thought ...
Thanks nate - this will come in handy.
|
#107
|
||||
|
||||
Re: More than just a thought ...
I am honored by the comments but the turn table was an idea by a good friend here on the board.
Like everyone else I gather ideas talk with friends ask questions and then go build something.... |
#108
|
||||
|
||||
Re: More than just a thought ...
It is an excellent idea, but when I was told about the turntables all I could picture was the one we have at work that takes a couple guys or a fork lift to get it on the mill lol. I've never seen one that small.
|
#109
|
||||
|
||||
Re: More than just a thought ...
hinesight says find an aluminum one. This cast iron is heavy.
|
#110
|
||||
|
||||
Re: More than just a thought ...
|
#111
|
||||
|
||||
Re: More than just a thought ...
Hmmmm.... Those hinges look familiar for some reason.
__________________
-J.D. |
#112
|
||||
|
||||
Re: More than just a thought ...
Ok so this version did not work out. Tried 2 different mounting with no improvement. Turns out my pivot is too far away from the door surface. So a new design and more printing to be done.
I broke rule 1 of design. Test your design. I was so anxious to make hinges I didn't properly test in my design models. |
#113
|
|||
|
|||
Re: More than just a thought ...
I'm no designer by any means, but what do you think about a "simple" Piano Hinge for the doors? I've seen a few 1:1's with those type of hinges on the doors. You might need to make cut outs for them, but I'm thinking they'd work, and should look ok as well.
|
#114
|
||||
|
||||
Re: More than just a thought ...
Chris,what an awesome project you have here.Its is over the top for sure.I feel your pain on the hindge issue, I spent a whole day on a hindge for the tilt hood on one of my trucks. Good grief.Ok back to work.Good job,
Ed |
#115
|
||||
|
||||
Re: More than just a thought ...
Guys thanks.
Piano hinge - yes I have a few lingering about. Have used them a lot. Was trying for the hidden look aND something nice tHan what i typically produce. I have the piano as a fall back punt option if all else fails. |
#116
|
||||
|
||||
Re: More than just a thought ...
|
#117
|
||||
|
||||
Re: More than just a thought ...
|
#118
|
|||
|
|||
Re: More than just a thought ...
I understand the wanting a hidden look, I'm sure, from what I've seen of your work, that you'll figure something masterful out. The rig looks awesome so far, I can only dream of having that one of talent.
|
#119
|
||||
|
||||
Re: More than just a thought ...
Much is just figuring it as I go. Like I must have my ratio off for the cab height. As you see the dash looks right with the windshield but neededva sub floor to get the seat height close and then it's like someone could stand and walk through the cab. In general it's close but not exact. The interior was a Sunday afternoon thought and a bunch of pieces here and there.
|
#120
|
|||
|
|||
Re: More than just a thought ...
Haven't seen any updates lately, is everything going ok? It looks great so far.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|