RC Truck and Construction  

Go Back   RC Truck and Construction > RC Truck's Ag and Industrial Equipment and Buildings > Construction Equipment > Construction Companies & Worksites


Reply
 
Thread Tools Display Modes
  #1841  
Old 04-22-2021, 02:05 AM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

#1 B50, it was this month in 2015 when it started hauling, I think it might of been Apr 15; I had to change bushings in the suspension beam, the axles were moving side to side way too much.



#1 has brushless drive motors, way more power to pull a pup up my 20* ramp out of the basement, the pup has brushed drive motors, the ADT itself doesn't have enough traction by itself to pull the pup up such a steep grade. Tried it out tonight, works pretty good, much better than the other ADT with brushed motors. I now have these 2 ADTs paired on a DX9, not quite enough channels so the pup dump & #2 ADT steering are on the same channel.





My new crusher from 911 Metal Lurgist showed up today.







It's a lil taller than the old Geneq crusher & an inch wider so it crush more material faster, hopefully nonstop with the loader feeding the screener.





Mounted up to the old the old Geneq frame today, just need to get a new longer v belt for it tomorrow & give a go. On 911 metal lurgist site, it recommends 1hp, but I'm gonna try with this 1/4hp motor 1st. The material I'm putting thru it has already been crushed once by the larger crusher & sized down to about 3/8.



__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1842  
Old 04-22-2021, 10:09 AM
9W Monighan's Avatar
9W Monighan 9W Monighan is offline
Big Dawg On The Bone
 
Join Date: Aug 2010
Location: Pittsburgh,PA.
Posts: 1,285
9W Monighan will become famous soon enough9W Monighan will become famous soon enough
Default Re: LilGiantsConstrCo

I have one of those or something similar. decal on side says "The Crunch" Never tried it yet. The big Morse I've had at Cabin Fever works very well but much larger.
Reply With Quote
  #1843  
Old 04-23-2021, 02:26 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

Are they both jaw crushers? I thought the one you took to cabin fever was a 2 roller crusher.
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1844  
Old 05-01-2021, 12:42 AM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

Got the new small crusher dialed in.

https://youtu.be/oYsDTD2WXPU
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1845  
Old 05-17-2021, 08:59 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

Getting some damp dirt moved out of the basement to ground level where it will dry out quicker. The unpainted cab that I put the pup on has brushless motors in the drive axles, way more power than brushed, the trk pulled it great up the ramp but it was time consuming & tight to dump on the pile... no more pup.

https://youtu.be/He00d6Gpxs8

Flat topping the pile for the next layer to dump on.

https://youtu.be/Ni1kA3CYtFs
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1846  
Old 05-21-2021, 01:46 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

Finished planting on Monday, time for hobbies again, getting some dirt hauled outside. The perimeter of the shop is done, so I'm just broadcasting the dirt out in my yard.

https://youtu.be/LCCAvsSCNLQ

So now that hauls are getting further away, time to build a 3rd cross dump trl... today I ordered from my local auto parts store a needle thrust bearing with an outside diameter of 78mm & a height of 16mm to put a steerable turntable between the rear of the trl & the drive axles to help get the long train around tight corners that 2 trls are barely clearing now... $270cdn... covid bs has made the world gone mad with inflation pricing!... anyways, I hope it's here in a week.



The weather outside today, suppose to be Spring...

__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1847  
Old 05-21-2021, 02:17 PM
frizzen's Avatar
frizzen frizzen is offline
Big Dawg On The Bone
 
Join Date: Jan 2016
Location: indy, indiana
Posts: 2,040
frizzen is on a distinguished road
Default Re: LilGiantsConstrCo

The new dig & haul videos looked really good, can't wait to see how the wiggle-wagon does with the extra trailer

Looks like that crops putting out a ton of white pollen.
__________________
What do ya mean "Cars are neither Trucks or Construction"?
It's still scale, and i play fairly well with others, most of the time...
Reply With Quote
  #1848  
Old 05-21-2021, 03:34 PM
jerry56 jerry56 is offline
Craftsman
 
Join Date: Apr 2019
Location: WV Panhandle
Posts: 761
jerry56 is on a distinguished road
Default Re: LilGiantsConstrCo

I don't know but looks like it could be spring in Saskatchewan to me...you can still see dirt and grass...
Reply With Quote
  #1849  
Old 05-25-2021, 09:49 PM
skeeter skeeter is offline
Big Dawg On The Bone
 
Join Date: Jul 2017
Location: Washington State
Posts: 1,732
skeeter is on a distinguished road
Default Re: LilGiantsConstrCo

I'm excited to see the newest addition to the trailer fleet hard @ work!
Reply With Quote
  #1850  
Old 06-02-2021, 03:16 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

That snow along with some rain mid week added up to a good bit moisture to get the crop off to great start... and I guess the world market thought so too b/c everything dropped 30% last week.

I found a cnc water jet guy about an hr from my house & he's willing to work with me to cut out parts for my rc's... last Friday I got all the sheet cut for my next trl, + a new set of doors for my 1st cross dump, the one that is painted & always bind when closing. Get the welding done this week maybe to see that everything fits together properly & be testing 3 trls together on the wkend... if no changes needed, put in an order for 5 more cross dumps.

And I put a bug in his ear to draw up clam dump trls... I've got an article from a plastic model magazine from the 90's that showed step by step with measurements to build in 24th scale, my yellow clam dump BTrain for Tamiya semi was patterned from that article.





Got some dry dirt hauled out of basement last couple weeks, something to screen & crush on rainy days.





Soaked up another area in the basement a week ago, another week of drying & it could be prime for digging without being too muddy & sticky... spread a layer of rock chip over it so the tracks don't get gummed up with clay.



My next dirt work project has been canned or maybe postponed till this covid bullshyt pandemic goes away & construction costs somewhat normalize again, so for now I'm just gonna go deeper in the basement, take clay out & put gravel back in just to keep the fleet moving & somewhat interesting...

Got a bobtail load of what I thought/wanted was pea gravel last week, now I realize what I should've ordered was rock chips...I've tried running this through my crushers, my big crusher won't close enough to break it much & small crusher takes forever b/c it's such hard rock... so this pea gravel will mostly be spread throughout my yard & some will go in deep in the basement & rock chip will be the final cover, 30 cubes from now.

__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1851  
Old 06-06-2021, 02:40 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

Got my 3rd trl box welded together this week... just need to make the front hitch & figure out the rear frame to make it steerable with a Actuonix actuator.





I put a mount on the 490 bucket to use with the 850, its shape & long teeth makes it an awesome digging bucket... the power of the 850 however, silver soldering not strong enough, a few spot welds with the mig to strengthen it.





The clay is really sticky, I'm using the 850 bucket to keep the trench wide... I'm digging a trench to start to get a straight wall bc these model excavators don't have the side way power to do straighten wall afterward unless you're digging directing at the face, make sense? Buffed the rust off the sides & bottom of bucket, and tried a couple of different lubricants hoping it'll glide through the trench easier... didn't do much & both were wiped clean after a couple of passes. I sharpened the teeth up too.





























Last 2 pics show the next cut being soaked up, start digging in July.



__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1852  
Old 06-06-2021, 02:48 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

A couple of vids spreading gravel over the damp clay so the 850's tracks don't clogged up & the start of the dig with the trench.

https://youtu.be/DNBoyxRdvog

https://youtu.be/gqq8cCU5G_Y

https://youtu.be/CyWZosq6FQ8
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1853  
Old 06-22-2021, 02:27 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

Got some dirt dug out & hauled up this last couple weeks.

https://youtu.be/VvLxGbBrF28

https://youtu.be/zToKplW31Nc

Now that crop spaying is mostly done for awhile, get back to finishing building the crossdump trl & graveling my yard with that pea gravel so I can get a bobtail of rock chips to haul to the basement, what I should've ordered originally.
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1854  
Old 06-22-2021, 06:05 PM
egronvold's Avatar
egronvold egronvold is offline
Big Dawg On The Bone
 
Join Date: Dec 2010
Location: Conshohocken, PA
Posts: 1,445
egronvold is on a distinguished road
Default Re: LilGiantsConstrCo

Time to get the popcorn and watch some videos
__________________
Emil G | MFZ Blocher Fendt 926 | RC4WD Volvo EC480 excavator | Carson LR 634 | Kenworth 6x6 hauler | Kenworth 6x6 dtrk
My channel:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Construction site on Facebook:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Pictures on Instagram:
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Reply With Quote
  #1855  
Old 07-27-2021, 04:18 AM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

I haven't touched my 3rd cross dump trl since I last reported about it, just no build ambition, but I have moved lots of material in the last month... dug a deeper hole in the basement, hauled some of the dirt out of the basement out & moved lots of rock into the basement.













Now as of today I'm just scraping up the last of pea gravel to spread around my yard.. probably won't be till after harvest that I order a bobtail of rock chips.







I got this "lazy susan" turntable from a neighbor earlier in the month, super handy tool for painting rims and other large assemblies like frames & cab.



A few movies from the activities the last month.

https://youtu.be/aWj7WNLZw1U

https://youtu.be/Dtk5Lgn2rnk

https://youtu.be/dloFlDZRwec

https://youtu.be/Uf4fT0-jsvk

https://youtu.be/gVrtvOsggR8

https://youtu.be/FMfX7eLSGfA

https://youtu.be/MuqX623fL7s

https://youtu.be/hBS7EzHDexk
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1856  
Old 08-09-2021, 06:30 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

Got the last of the gravel tidied up last week...





https://youtu.be/hBS7EzHDexk

Friday this showed up... Fumotec's WA470





The cab & rear grille are magnetic placed so you can get to the guts of the machine easily; just 2 bolts to remove engine hood & 2 more to remove bumper. The way this model is configured needs 10chs, but I only got 9ch rx, so the servo operated engine hood lift won't be used.





for/rev
steering
boom
bucket tilt
quick coupler (hyd)
extra hyd valve (a high dump bucket coming soon)
2 spd trans
diff locks
hood tilt
pump

Go put the rx in now & tune it up... plus take off a bunch of delicate 3D printed parts like the rear mudflaps, handrails, front fenders, put em in a box. Got no job for the loader atm, doing a shyt ton of painting right now, don't want to make any dust crushing, screening, hauling.
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1857  
Old 08-11-2021, 09:00 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

Couple vids of the new loader, just getting the feel of it.

https://youtu.be/ssydenjnt64

https://youtu.be/ysUo6cuL_DM
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
  #1858  
Old 08-15-2021, 08:53 AM
calum_scania's Avatar
calum_scania calum_scania is offline
Newbie
 
Join Date: Apr 2014
Posts: 108
calum_scania is on a distinguished road
Default Re: LilGiantsConstrCo

Just finished watching your video on the WA470 it looks a nice machine I hope you're impressed with it?

I was surprised to see another loader with you having the old Stahl and the WA500 on your bench?

Calum
Reply With Quote
  #1859  
Old 08-17-2022, 03:38 AM
Max187 Max187 is offline
Newbie
 
Join Date: Sep 2015
Posts: 1
Max187 is on a distinguished road
Default Re: LilGiantsConstrCo

News??
Reply With Quote
  #1860  
Old 01-31-2023, 09:17 PM
Lil Giants's Avatar
Lil Giants Lil Giants is offline
BANNED
 
Join Date: Aug 2010
Location: Saskatchewan
Posts: 4,431
Lil Giants has disabled reputation
Default Re: LilGiantsConstrCo

What’s new? Lots of things.. if you’re subscribed to my utube channel you’ll have seen.. not sure how many vids over the last 2yrs, still digging crushing screening several cubic yards every yr. Been fixing, updating, rebuilding quite a few models this winter. Presently building a new model this week.









__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get!

Joe
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 6 (0 members and 6 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:13 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.