reinke 48'x102 drop deck

[ihbuilder]

I worked a deal awhile ago with Reeve to build him a drop deck like a 1:1 he has . Now if you don;t know me by now , I like to make things as close to the real thing as possible since my mill predates cad/cam I'm basically programing the long way (G code ) (at least for frames ) I had hopes to mill the frame rails with the suspension hangers , BUT with the jumping on the x it just not gona happen I was all set to run them but I can't get the end mills I need today and editing this thing is a PITA but here it is on paper I hope to have some frames in the next week or 2 as the 1:1 life has me busy again



A link https://rdss.reinke.com/public/drop_deck.html

[Car5858]

I will be following this build

As for the jumping on the X axis, what are your steps set to, and what operating system is the mill using?

[ihbuilder]

Originally Posted by Car5858

I will be following this build

As for the jumping on the X axis, what are your steps set to, and what operating system is the mill using?

soon to get hit with a BFH pre dates PC Centurion IV by milltronics no longer supported there's more then that wrong with it . I think this POS is getting yanked out by next weekend hopefully when the newer 1 comes and just figure how to do it with the smaller table this deffinately needs a new control any one need a boat anchor !! Cheap!!!!!

[Car5858]

LOL you mean a one time use boat anchor.

There are documented problems with this contoler atfter conversion to single phase. The inverter is not able to handle the change well, causes jumpping and HS travel when you try to use grid function.

Try swapping Z and X cards and see if the problem occures on the Z. This should help isoulate the problem.

Sometimes the floresent lighting also interfers with the siginal.

These are just some of the results found.

Personally I would put a xylotech drive on it. I am running this on my router with 406 inoz steepers at 1/8 steps with good results.

[ihbuilder]

I can run it in jog with no problems It just starts to f up in hand wheel mod or running programs It can't even run a simple program out of the manual all was going OK till after lunch I guess it wanted a lunch break to It's coming out of the shop by this week end making room for the VMC and lathe I just had it with it my uncle said He sees this all the time people buy these 20+ year old machines thinking they got a deal . 10 K will get me a new control from mm and last anther 20 + but I don't have the time to refit right now and I want to get these things done for these ppl .

[ihbuilder]

As you all know I got a newer mill AND at long last I'm getting this frame cut out It's nice to work in you sleep for a change well the machine does

OK inside profile is done on phase 1 next stringer holes and outside profile tomorrow then they're ready to be flipped over to do the 2nd phase of course I threw some parts for my mack M75SX build in the process
from the set up :







more tomorrow I hope
thanks for looking

[ihbuilder]

well a little more then a piece of alm. plate in the mill








thanks for looking

[hauler_10-4]

Wow those rails came out great. Cant wait for the next update.

[Dreamweaver]

Those are lookin good Steve.. Careful look what happened to Travis when he made ONE trailer.. Some of us others might want one of them..

~Mike~

[DuelTruckDriver]

Quality Steve Those turned out like a champ, can't wait to see more! > Marty<

[ihbuilder]

Originally Posted by Dreamweaver

Those are lookin good Steve.. Careful look what happened to Travis when he made ONE trailer.. Some of us others might want one of them..

~Mike~

thank you Mike , well if that happens then it does

Originally Posted by DuelTruckDriver

Quality Steve Those turned out like a champ, can't wait to see more! > Marty<

thank you , Marty


A little hair pulling again today but all in all the end result put this on my face .



more later

[Brian in PA]

Looks good Steve its nice to see your putting your new mill to work!

Brian

[Tamiya Cowboy]

Going to be another IHB work of art!!

[4EX]

gonna need one of those for the fleet

[ihbuilder]

thanks Paul I know It's been awhile I'm starting to pick back up on things . I'm getting closer to welding up the stringers . made a new tail piece with the right kind of light holes ( need to ream them a little for a perfect fit ) . suspension/axles just about finished (air bags yet )

[REEVE2007]

LOOKIN SWEET!!!

[Brian in PA]

Nice attention to detail Steve!

Brian

[rockNmayhem]

Steve, the trailer is looking great as usual. I had almost forgotten this thread. I'm glad to see some updates on this trailer build.

Tyler

[spudd]

Wow!!!!! that is outstanding.a true work of art

[ihbuilder]

I know it's been awhile I was waiting to get a tig to weld it together . thanks to smokin joe I got 1 . after a couple trial welds , I felt it would look like dog crap if I tried . So , back to the cad , and milled out cross members with the bracing .





thanks for lookin