|
Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Bruder Liebherr loader build
Starting on the loader,have a long way to go on it.Already have a few parts.
Using the same 6 channel transmitter as on my hobby engine excavator,just ordered a extra reciever a while back.Have to order two more gear motors,and the servos,a little at a time,lol. Started on the front portion,using 22 guage sheet metal.Will be using screwdrives.Going to make a scratch built boom next.Trying to get the front portion done,then the rear.Have some more wheels I may use,see how it goes.Have a few pics so far. |
#2
|
||||
|
||||
Re: Bruder Liebherr loader build
Few more pics
|
#3
|
|||
|
|||
Re: Bruder Liebherr loader build
looking good so far. Can't wait to see it working along side your excavator.
|
#4
|
|||
|
|||
Re: Bruder Liebherr loader build
Thankyou Pumptech. I have been looking everywhere for a detailed conversion on the Bruder Loader. I can't wait to see how you do it..
|
#5
|
|||
|
|||
Re: Bruder Liebherr loader build
Although after looking at your pictures I know I do not have the necessary metal skills that you have and will have to devise a way to do a conversion with the existing plastic. Or JB Weld enhanced plastic lol.
|
#6
|
||||
|
||||
Re: Bruder Liebherr loader build
Quote:
Hope the pics look ok,had to take with my phone,something happened to my camera,must have gotten dropped,doesn't work,may be awhile for some vids,until I replace it. |
#7
|
||||
|
||||
Re: Bruder Liebherr loader build
Quote:
The rear section of the model is going be a little tricky with the swivel axle,have a few ideas already. |
#8
|
|||
|
|||
Re: Bruder Liebherr loader build
Try to keep it light. My track loader is just about the limit on what the actuators can move.
|
#9
|
||||
|
||||
Re: Bruder Liebherr loader build
Cool project Neil! It will be fun watching this come together.
__________________
Scott "No load is too Small" |
#10
|
||||
|
||||
Re: Bruder Liebherr loader build
Yes, I agree. Neat looking project, and I can appreciate your metal fabrication skills. The front half of the loader is looking good, rebuilt with metal. I would like to see some larger photos, if it's possible. Your pictures are a little on the small side. Keep it up!
__________________
Nathan |
#11
|
||||
|
||||
Re: Bruder Liebherr loader build
Thanks ,going to try to.
|
#12
|
||||
|
||||
Re: Bruder Liebherr loader build
Quote:
Who's Neil ? Talk to you later ,Tommy |
#13
|
||||
|
||||
Re: Bruder Liebherr loader build
Quote:
|
#14
|
||||
|
||||
Re: Bruder Liebherr loader build
Quote:
I would like to see larger pics as well.
__________________
Scott "No load is too Small" |
#15
|
||||
|
||||
Re: Bruder Liebherr loader build
LOL! Did somebody call me?
Hey Pumptech, I'm the one with the Kyosho Hanomag loader manual, if you want a copy, pm me. Richard/vanisle & Travis have copies already for screw drive idea's. Look's like a neat project. Cheer's, Neil. |
#16
|
|||
|
|||
Re: Bruder Liebherr loader build
I wonder if your screw drives could be made to be used for the turning rams.
|
#17
|
||||
|
||||
Re: Bruder Liebherr loader build
Quote:
Thanks for offering ,going to try the auger bit method first,same as my excavator,see how that goes,seem to get good power from them.If that doesn't work may have to give you a ring,thanks again. Tommy |
#18
|
||||
|
||||
Re: Bruder Liebherr loader build
Hey Mike ,I thought about that,was leaning more on using a high torque servo with linkages.Have played around with sliming the screwdrives down,leaving off the 1/2 SST ,using 3/8 and 1/4 ,with a smaller auger bit that fits in the 1/4.Then of course have to keep space in mind for the battery/electrical gear.
|
#19
|
||||
|
||||
Re: Bruder Liebherr loader build
Hey guys this post was mainly to check pic size,looks bigger on my end.
Little progress tonight,got a couple of the boom arms cut out so far,its a slow go. Uploaded with ImageShack.us Last edited by pumptech; 11-08-2011 at 10:25 PM. |
#20
|
||||
|
||||
Re: Bruder Liebherr loader build
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|