|
Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
|
Thread Tools | Display Modes |
|
#1
|
||||
|
||||
Re: 990 cat loader
Thanks for the quick reply! I'm also investigating how a self molded tire can be made. I can't wait to see your's finished
|
#2
|
||||
|
||||
Re: 990 cat loader
Steve, can you share some info about the gear motors?
First: as i read in most of the gear motor specifications, if the output shaft is blocked, it can damage the gears. Let's assume, that the shaft is never blocked cause it have enough power to drive the big wheel, but what happens if you turn (left or right) while the machine is not moving, are the wheels turning as expected, or are they still and sliding on the floor? (hope you can understand what i mean). Secondly can the wheels turned by hand (slowly ofcourse), or could this also damage the gears? (the 2 questions are the same, i know) I know this mostly depends on the gear ratio you're using, as i calculated, to get the max speed (1:1 -> 22 km/h, 1:14,5 -> 1,5 km/h), a max output of 50 rpm is needed. So i think, the best is a lower rmp motor as base to get the lowest gear ratio possible... Last edited by AbelVincze; 10-05-2013 at 07:24 PM. |
#3
|
||||
|
||||
Re: 990 cat loader
Abel , I didn't go with the 4 gear motor set up in the end . Even they where to flimsy for the size and weight Of the machine . I went with a differential set up which seems to be holding up quite well I don't have any experience on using a gear motor at each wheel yet
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#4
|
||||
|
||||
Re: 990 cat loader
Steve, ok thanks, i thought you've tried it... For some reason i don't trust these gear motors either...
|
#5
|
||||
|
||||
Re: 990 cat loader
Hi again.
In the last 2 month, i collected a huge number of Cat blueprints, with aid of these documents, i built a 3D model in 1:14,5 with every little details - Some of the inside mechanics are still missing, but they will be done shortly. Steve, before going further i will make a new thread for it, but if you don't mind, i share the results here: https://www.behance.net/wip/316985/659439 PS ederson wrote in portuguese, and means: Congratulation perfect, and: cool. |
#6
|
||||
|
||||
Re: 990 cat loader
thanks Abel , if i heard it said I would've recognized it but makes sense now
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#7
|
||||
|
||||
Re: 990 cat loader
|
#8
|
||||
|
||||
Re: 990 cat loader
That's great way to make those pins!!! I've been thinking on how to do such. Sometime in future I'm going to use your idea and get rid of the c-clips I'm using on pins. I tried to make the flats undersized and press pins into but just not enough material to make tight enough and reliable. And loader looks great!!!
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#9
|
||||
|
||||
Re: 990 cat loader
The pins came out nice and the loaders looking better all the time, but what I really like is the jig you made to mill the pins! Nice job! Sometimes the set ups harder than actually making the part.
|
#10
|
||||
|
||||
Re: 990 cat loader
Steve,
Nice detail!!! I agree, normally it takes longer to setup a part than run it. |
#11
|
||||
|
||||
Re: 990 cat loader
Great work on those pins, Steve! 16" of reach makes this Cat a monster!
__________________
Nathan |
#12
|
|||
|
|||
Re: 990 cat loader
nice build but noticed u steal haven't done the up grade to the tires barn hausen modellbau might be a good answer he has a large selection
|
#13
|
||||
|
||||
Re: 990 cat loader
I have some on order since Christmas from RCM which I think barnhausen makes them for RCM, not a werd yet . I tried Barnhausen directly with no reply . I was hoping to have them for this week end There was only 1 size I saw that was close .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#14
|
||||
|
||||
Re: 990 cat loader
So what's the bore size of your new lift cyls?
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#15
|
||||
|
||||
Re: 990 cat loader
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#16
|
||||
|
||||
Re: 990 cat loader
holy jeepers looks like I'll get new tires after all
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#17
|
||||
|
||||
Re: 990 cat loader
Pictures or it's not happening.....
|
#18
|
||||
|
||||
Re: 990 cat loader
I just got the bill gotta wait for them to come across the pond waaaaaaa
here's what they supposed to look like http://www.rc-machines.com/de/search...ords=RCREI8062
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Last edited by ihbuilder; 04-26-2014 at 05:16 PM. Reason: added link |
#19
|
||||
|
||||
Re: 990 cat loader
All I see is an awesome drop deck trailer.....
__________________
Nathan |
#20
|
||||
|
||||
Re: 990 cat loader
Nice Can't wait to see it installed.
I checked the site from where you ordered the tires, but unfortunately i didn't find the right size (D 173mm, 75mm, inner D68mm). I will ask them if they are making custom size tires. |
Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
|
|