Bruder Delta tracked loader

[Trixx]

Hi,

How do you use the channels on the radio?

Somthing like my drawing?

/Andreas

[Lil Giants]

The bottom drawing is how I like to operate.

Nifty drawing, I saved it to modify later in "paint" for future explanations of how set up radios.

[SmallHaul]

Originally Posted by Trixx

Hi,

How do you use the channels on the radio?

Somthing like my drawing?

/Andreas

The bottom drawing is how I like to operate but, I steer with my right.


I decided I should keep the prototype Loader for myself and run the heck out of it to make sure everything holds up nice. After running it for a couple of hours moving dirt I noticed that the motors where getting really hot because of the 205:1 transmission that I was using. If you listen to motors in the video they are screaming at anything over half throttle. So, I put the heavier duty tamiya tranny in it (the gears are twice as thick) and now the drive ratio is 115:1 and now the motors never go over 130 degrees even after 1 hour of constant work. It still has power to spare and it sounds much better without the motors screaming.

I was asked to make a video with it running slower. I didn't realize that a Cat 297C has a top speed of only 8.5 mph.

http://www.youtube.com/my_videos?feature=mhum

[firefighter-1177]

The bottom drawing is how our cat skidsteers at work operate.

[ihbuilder]

yes the bottom is cat joystick setup boom bucket on the right and on the left stick for skid - fwd/rev left/right on ex - crowd and swing . what's neat about what cat did with the skid steer controls , is they match the excavator controls . just instead of swing your steering and instead of crowd in / out your traveling

IHSteve

[SmallHaul]

I'll have to switch my crane & skid steer to the Cat setup then.

The full scale equipment operators that have run my crane & skid steer have said that its backwards to what they are used to.

[ihbuilder]

Originally Posted by SmallHaul

I'll have to switch my crane & skid steer to the Cat setup then.

The full scale equipment operators that have run my crane & skid steer have said that its backwards to what they are used to.

Hmm , then I guess I didn't get to run them yet . That would've been a sight

[SmallHaul]

Originally Posted by ihbuilder

Hmm , then I guess I didn't get to run them yet . That would've been a sight

I thought you ran my Dragline Crane?

The rubber tracked loader has 20 hours of run time on it now and everything held up great. Even the tracks are still fine. So, I feel completely comfortable selling these. Albert (Aseejr) is my first customer and I have his loader over halfway complete.

I made a quick video moving some timber around so, now Albert can help move logs around the next time he visits Lou (trancksntreadslou) and Greg (RCLogger).

http://www.youtube.com/watch?v=Lr14XmWN7JM

[Snochaser]

Nice Scott. Now for more attachments huh? A log grapple broom or Fecon head? hmmmm

Ben

[TheMachinist]

Just watched the video. love the Quick change and the loader seems to have lots of power. I can't wait to see Alberts when it arrives.

[SmallHaul]

Originally Posted by Snochaser

Nice Scott. Now for more attachments huh? A log grapple broom or Fecon head? hmmmm

Ben

Thanks Ben. Bruder sells the bucket by itself for less than $3. it would be fun to buy a couple to mess with and make some other attachments out of it.

[aseejr]

Sold again. Impressive.

[td9clyde]

a 4 in 1 bucket would be cool but kinda hard then you could bit stuff to pick it up or you could use it to gradeout the sand or rubber chips

[SmallHaul]

Originally Posted by aseejr

Sold again. Impressive.

Thanks!

Originally Posted by td9clyde

a 4 in 1 bucket would be cool but kinda hard then you could bit stuff to pick it up or you could use it to gradeout the sand or rubber chips

That would be cool but, I think it would be very bulky to add another servo to move it.

Well, the first production unit is finished (Aseejr's Loader:-)

Here is a video of it to show the finished product and how the radio is set up. The steer & drive are on the right, lift & curl on the left. If your radio has a spring loaded center on the throttle you could run the tracks with the left stick. But, without a spring loaded center it would probably be hard to find the center/neutral to stop the loader from creeping when you want to stop moving.

http://www.youtube.com/watch?v=_y0kSpmeoxk

I am starting on Doug's (Firefighter30) next

[9W Monighan]

I love it!
But I can't here anything, I don't have speakers here at work. My new monitor didn't have them built in .

[Tamiya Cowboy]

Scott

You are amazing at building these conversions it so great watching you convert these you have some dang good skills..

[woodhog]

loader looks great .what will conversion price be?

[SmallHaul]

Originally Posted by Tamiya Cowboy

Scott

You are amazing at building these conversions it so great watching you convert these you have some dang good skills..

Thank you very much Paul.

Originally Posted by woodhog

loader looks great .what will conversion price be?

Thanks. I'll shoot You a PM.

[dirtpusher9]

Scott, when I try to watch your videos it pulls up my(dirtpusher9) videos, not sure whats going on.

[ihbuilder]

Originally Posted by dirtpusher9

Scott, when I try to watch your videos it pulls up my(dirtpusher9) videos, not sure whats going on.

yea me too but just this 1

bring it up here and we'll how it does in my shop you'll need a grapple bucket on it though