carp
01-07-2016, 03:26 PM
A few years back I made an excavator it was a first attempt but not very good, so I decided to have another go, I have completely remade the under carriage but for now have reused the old boom arm and bucket, hopefully in the future it will be replaced but seems ok at the moment.
Tracks are made from k1 attachment chain and tracks made from aluminium angle, my girlfriends dad then took them all to work and got them anodized. Motors are mfa como 970d planetarys 105:1, they are attached to angle grinder heads which have a 3:1 reduction, I may upgrade the Motors to brushless at some point to improve the travel speed slightly.
I used a China cat slew bearing it work a ok but I don't think it will hold so I'm going to change it to a taper bearing set up and possibly 2 slew Motors.
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG2102_zpsw78gbeox.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG2102_zpsw78gbeox.jpg.html)
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG2101_zpsix9oe0co.jpg
(http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG2101_zpsix9oe0co.jpg.html)http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG1814_zpsdbmivn2q.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG1814_zpsdbmivn2q.jpg.html)
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG2104_zpsgzvt0dzr.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG2104_zpsgzvt0dzr.jpg.html)
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG1821_zpsawtj6qoa.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG1821_zpsawtj6qoa.jpg.html)
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG1822_zpsyahkans0.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG1822_zpsyahkans0.jpg.html)
Tracks are made from k1 attachment chain and tracks made from aluminium angle, my girlfriends dad then took them all to work and got them anodized. Motors are mfa como 970d planetarys 105:1, they are attached to angle grinder heads which have a 3:1 reduction, I may upgrade the Motors to brushless at some point to improve the travel speed slightly.
I used a China cat slew bearing it work a ok but I don't think it will hold so I'm going to change it to a taper bearing set up and possibly 2 slew Motors.
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG2102_zpsw78gbeox.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG2102_zpsw78gbeox.jpg.html)
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG2101_zpsix9oe0co.jpg
(http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG2101_zpsix9oe0co.jpg.html)http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG1814_zpsdbmivn2q.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG1814_zpsdbmivn2q.jpg.html)
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG2104_zpsgzvt0dzr.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG2104_zpsgzvt0dzr.jpg.html)
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG1821_zpsawtj6qoa.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG1821_zpsawtj6qoa.jpg.html)
http://i1376.photobucket.com/albums/ah35/jarvis45/tractor/IMAG1822_zpsyahkans0.jpg (http://s1376.photobucket.com/user/jarvis45/media/tractor/IMAG1822_zpsyahkans0.jpg.html)