My new Knight Hauler/Freightliner

[540-MAN]

Here is the progress of my new Knight Hauler/Freightliner that I received a month ago. There is still a lot to be done to it before it's finished but cant wait.

We are still trying to come up with a colour scheme, looking at putting guards on the rear tyres, Starting from scratch on building a bullbar for it, Some extra lights, waiting for my new aluminum rims for it now after I order some more, plus some other stuff that will come to mind as I'm building it.

I was wondering also if anybody knows where I could possibly get some clear lenses from that will fit the rear lights?

http://imageshack.com/a/img809/3116/mgj3.jpg

http://imageshack.com/a/img38/7568/y6ba.jpg

http://imageshack.com/a/img812/2517/1uiv.jpg

http://imageshack.com/a/img62/8404/vco1.jpg

Here is the bullbar I'm looking at making for it below.

http://imageshack.com/a/img838/1526/ca7p.jpg

[Diesel Demond]

sweet great start!

[Ekimjr]

very nice still working on my own...

ekimjr

[MACK Daddy]

Nice start....love the aggressive look with the rear tires


Alfy

[540-MAN]

Thanks guys it gonna take abit of time.

[540-MAN]

There will be no dash going in as there is no room because of the sound box just gonna tint the windows.

[Exclusive RC]

Nice start so far, I see another great truck in the future...

[540-MAN]

This will be my third truck that I have owned.

[Exclusive RC]

whats your plan for headlights and grill?

[Billy832]

There will be no dash going in as there is no room because of the sound box just gonna tint the windows.

You know, you could actually use the interior if you wanted to. My knight has the interior and the full mfu, and I can tell you with no hesitation my building skills are nowhere near most of the guys on here. I just built a sleeper wall that squeezed between the cab and sleeper, even made a drape for it, painted the wall black, rearranged a few things, and got it all to fit

[540-MAN]

whats your plan for headlights and grill?

I'm hoping to change it to the same as the photo above but don't know who would be able to do it for me and make the grill for it so it will stay as it is and try to make some changes that I can do to make it look like a freightliner as close as I can.

[Cossett]

I'm hoping to change it to the same as the photo above but don't know who would be able to do it for me and make the grill for it so it will stay as it is and try to make some changes that I can do to make it look like a freightliner as close as I can.

whats your plan for headlights and grill?

Would it be possible to use the head lights of the new freightliner cascadia evolution providing you can get the lights as spare parts as theyabout the same as the freightliner you posted along with the grill ???

Cheers Tracy

[540-MAN]

Your probably pushing it to buy any parts from that truck as it has only just been released and there would be a fair bit of modifying to do to get it to fit.

[540-MAN]

I have made progress on my truck in the last week the photos will be up soon on how much I made but its still along way to go.

I was wondering where I can get a stone guard for it for my front windscreen? I have seen a Scania on one of the Facebook pages and it had one on it. Is there any for the knight hauler?

[540-MAN]

Here are the progress photo's of my truck.

http://i1374.photobucket.com/albums/ag412/Shaun_North/newtruck5_zpse5976270.jpg

http://i1374.photobucket.com/albums/ag412/Shaun_North/newtruck6_zps0ab5c03b.jpg

http://i1374.photobucket.com/albums/ag412/Shaun_North/newtruck4_zps48dbdf2a.jpg

http://i1374.photobucket.com/albums/ag412/Shaun_North/newtruck2_zpsb3242730.jpg

http://i1374.photobucket.com/albums/ag412/Shaun_North/newtruck1_zps34b083e1.jpg

http://i1374.photobucket.com/albums/ag412/Shaun_North/newtruck3_zps631edc29.jpg

[flatdeck]

Looks good.. What colours are you going to us. Have you got that far..

Wayne

[bruce]

Looking good coming along nicely

[1985 kenworth]

Looks great so far :D

[540-MAN]

Still haven't come up with a colour scheme yet it will stay white for awhile.

[540-MAN]

Still looking for the following part if anybody can help.

MAN mirrors with the chrome inserts
Rear guards off a container trailer
Stone guard for front window

That should be it at the moment until I can think of something else.

If anybody can help that would be great

Thankyou

[540-MAN]

Still looking for parts in the above post.

[thebat]

looks great so far hey can i ask you to get me the part numbers for the tail light pods and the lenses for the rear and the cwenter reverse lamp set id like to put them on my king hauler thanks.

[540-MAN]

I'm having a problem with my truck now so I hope somebody can help me with it.

I gave it a test run the other day and everytime I put it in third gear with trailer on and the stick is flat out on the radio it shuts the truck down. Then when I take the trailer off it seems to run fine with out any problems.

I have checked all the wiring to make sure everything is connected and even fully charged the batteries but still no change so it has got me stumped of what is wrong with it.

Has anybody got any ideas of what it might be?

[mavrick0]

Sounds as if you are overheating the ESC and it is going into thermal protection mode and shutting things down. Without the trailer there isn't the load on the ESC so there is no reason for it overheat. Not knowing what trailer you are running I'm going to assume it's probably heavier then the stock Tamiya trailer. One suggestion would be to change the pinion on the motor and drop it down a tooth or two or try going to a crawler motor that has more torque for pulling but not as fast as the stock motor.

[Stuff]

are you running an MFC?

the other day I jammed mine into 2nd and it caught funny and shut down the truck. Maybe check the tranny to make sure you have 3rd assembled right? only thing i can think of.

[540-MAN]

Yes I am running a mfc unit in my truck and it is installed the same way as my old one I had. The tranny is all ok and put together as per instructions. I have no idea what is going on. The receiver doesn't have a Ariel on it where the other trucks I had did so I'm just wondering whether it maybe coursed by this or not as the cab might be blocking connection.

[Backlash]

Have you got the little limit switch connected up under the 5th wheel?

Have you got another battery to try?

What exactly happens when it shuts down in top gear? Do you just lose drive, or do you lose everything (i.e. no steering, drive or gearshift)

Does it happen as soon as you select top gear, or can you drive it for a while?

What do you need to do to reset the truck..? Is it just a matter of selecting 1st or second gear or removing the trailer, or do you have to turn it off, and then back on to get it to go again?

Is your radio 2.4GHz, or crystal type (27MHz, 29Mhz or 40Mhz)??

Have you used this radio with the MFC before?

Is it an MFC01 or MFC03?

[540-MAN]

Have you got the little limit switch connected up under the 5th wheel?

The 5th wheel switch is locked on all the time with or without trailer.

Have you got another battery to try?

I have 2 batteries and they are near new.

What exactly happens when it shuts down in top gear? Do you just lose drive, or do you lose everything (i.e. no steering, drive or gearshift)

When it's in top gear the whole thing shuts down like it does when the battery is flat and starts up again.

Does it happen as soon as you select top gear, or can you drive it for a while?

If the stick on radio is half throttle it runs fine but as soon as the stick on the radio is flat out it shuts down.

What do you need to do to reset the truck..? Is it just a matter of selecting 1st or second gear or removing the trailer, or do you have to turn it off, and then back on to get it to go again?

I have reset the MFU about 3 times so far thinking it might be that but nothing. 1st and 2nd gears are fine not a problem.

Is your radio 2.4GHz, or crystal type (27MHz, 29Mhz or 40Mhz)??

The radio is a 2.4GHz.

Have you used this radio with the MFC before?

I have never used this radio before at all.

Is it an MFC01 or MFC03?

MFC01, I have always used these ones in my other trucks I had and never had a problem with them.

Also the below photo is a photo of my receiver for my truck and I was wondering whether anybody could tell me whether there needs to be a ariel on it because it doesn't have one and I'm thinking the cab might be breaking connection and that's why it could be shutting down.

http://i1374.photobucket.com/albums/ag412/Shaun_North/receiver_zps6c3ad2b3.jpg (http://s1374.photobucket.com/user/Shaun_North/media/receiver_zps6c3ad2b3.jpg.html)

[540-MAN]

What truck looks like so far.

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0417_zps492bb447.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0417_zps492bb447.jpg.html)

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0418_zpsc7be6448.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0418_zpsc7be6448.jpg.html)

[540-MAN]

Sounds as if you are overheating the ESC and it is going into thermal protection mode and shutting things down. Without the trailer there isn't the load on the ESC so there is no reason for it overheat. Not knowing what trailer you are running I'm going to assume it's probably heavier then the stock Tamiya trailer. One suggestion would be to change the pinion on the motor and drop it down a tooth or two or try going to a crawler motor that has more torque for pulling but not as fast as the stock motor.

This is the trailer I'm running at the moment which it is a normal Tamiya trailer.

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0329_zps8fdf4e39.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0329_zps8fdf4e39.jpg.html)

I have never had any problems with my last trucks of towing this trailer sometimes it has A-trailer in front of it.

[mavrick0]

When the truck shuts down how long does it take for it to be usable again?

[540-MAN]

Straight away it goes like when the battery is flat shuts down then starts up again.

[mavrick0]

What might be happening is the voltage is dropping below the minimum that the receiver needs and shuts off. This is known as browning out. What causes this is the BEC voltage in the MFU dropping below that minimum that the receiver needs to run. One way to test this, which is kind of tough in our situation, is using an external power source to power the receiver. To do this you would need to use a y-harness since we use all of our slots in the receiver with the MFU and you'd have to disconnect all the red wires coming from the MFU to go into the receiver.

[fhhhstix]

What might be happening is the voltage is dropping below the minimum that the receiver needs and shuts off. This is known as browning out. What causes this is the BEC voltage in the MFU dropping below that minimum that the receiver needs to run. One way to test this, which is kind of tough in our situation, is using an external power source to power the receiver. To do this you would need to use a y-harness since we use all of our slots in the receiver with the MFU and you'd have to disconnect all the red wires coming from the MFU to go into the receiver.

I believe you are 100% correct. The MFU does not have enough BEC for all 3 servos when the truck is under a load and it shuts down the receiver which shuts the MFU down.

I had this problem with my new CASCADIA build, the MFU worked fine on the bench but in the truck and not even driving the servos pulled more amps than the BEC could provide so the truck just sat there turning on and off. I unpluged the fifth wheel servo, and unhooked the truck would start up and idle until I operated the shift or steering servo. I was using 3 HiTec 645MG servos which were just way too power hungry. I replaced them with standard servos and the truck works fine now. Plus be sure to set the endpoints of the servos to keep them in the operating range of the mechanics it is hooked to.

Travis

[yoyo]

Looking goog. Just love those drive tires. Much more realistic than the tires that come with the kit

[rctrucker2]

540-Man

I really like those aluminum rims you have on your truck. What brand are they and from whom did you order? Are they of good quality? I would like to get a set of aluminum rims for my new Freightliner Cascadia build. I have also seen mention of “Steve’s Rims” in several threads but I have not been able to find a link to them, just the reference. If anyone can direct me, I would also appreciate that information. Thanks for your help.

[Backlash]

OK, the reason for the questions that I asked..

AND Yes, I'm thinking a power problem, but I'm leaning more towards a battery issue than a BEC one.. (However, a battery issue can cause a BEC issue)

Have you got the little limit switch connected up under the 5th wheel?

With the switch connected, the MFU supplies less power to the motor when running without the trailer than it does with it fitted..

Have you got another battery to try?

I was thinking that the problem could be low quality battery packs, and the voltage is dropping below the requirements of the MFU when the using full throttle in a high load situation (like with the trailer attached).. This battery issue COULD also contribute or cause a BEC voltage issue..

What exactly happens when it shuts down in top gear? Do you just lose drive, or do you lose everything (i.e. no steering, drive or gearshift)

Just wanting to get an idea if the MFU is going into a fault mode, (i.e. tripping out) or if it is the receiver/ radio gear..

Does it happen as soon as you select top gear, or can you drive it for a while?

Wanting to know if it could be heat related..

What do you need to do to reset the truck..? Is it just a matter of selecting 1st or second gear or removing the trailer, or do you have to turn it off, and then back on to get it to go again?

Wanting to know what you needed to do to get the truck going again..

Is your radio 2.4GHz, or crystal type (27MHz, 29Mhz or 40Mhz)??

Regarding your concern for no Aerial wire on the receiver.. No aerial is not uncommon in 2.4Ghz systems..

Have you used this radio with the MFC before?

Could the radio be faulty?? Do you have another known working Radio and receiver that you could swap into the truck and see if the problem still occurs??

Is it an MFC01 or MFC03?

Was not sure if the MFC-03 had an inbuilt LiPo cutoff.. I have heard of similar problems occurring with low quality batteries, and high power Brushless motors, and when the ESC has a LiPo cut off turned ON..

No disrespect to the others, but I just cant see how it could be just a BEC issue, when all that you are doing is moving to full throttle in top gear..

HOWEVER, I could see it being a battery issue, where the additional load from the trailer and top gear is causing the battery voltage to momentarily drop below the requirements of the MFU's inbuilt BEC, and thus causing the MFU and radio to "stutter" and stop..

Much of this fault finding is a process of trial and error.. Here are some things that you can try (ONE AT A TIME)..

*If you have another working radio and receiver, try that instead of the Tamiya/Futaba unit..

*If you can borrow another battery off someone to try..

*If your using NiCd or NiMh batteries, and cant borrow another to try, completely discharge one of the batteries that you have, then put it on the charger (fast charge) and then put it in the truck as soon as it finishes charging and try that.. The voltage of a freshly charged battery will be slightly higher than one that has been sitting for a while.. (NOTE. DO NOT do this for LiPo batteries)

*If you think that it could be related to the MFU's BEC, then Disconnect the shift servo (and any other servo's or lights that run off the BEC) and leave ONLY the MFU and steering servo connected.. Manually move the shift servo into 3rd gear, and give it a test run..

*You could try a "stutter stopper" connected to one of the receiver ports, or via a Y lead.. Basically a "Stutter Stopper" is a capacitor that connects in parallel with the BEC.. Capacitors are devices that store a charge, and then can discharge it very quickly into a load.. With the Stutter Stopper connected, it will help to keep the BEC voltage at its correct level.. If you don't have, or cant buy a stutter stopper, you can make one from a 16V 4700 uf (micro Farad) electrolytic Capacitor, and an old servo lead.. Electrolytic Capacitors are polarity conscious, so connect the positive to the RED wire (for Futaba leads) and negative to the Black (for Futaba) and discard (remove/don't use) the white wire..

Mark..

[doodlebug]

540-Man

I really like those aluminum rims you have on your truck. What brand are they and from whom did you order? Are they of good quality? I would like to get a set of aluminum rims for my new Freightliner Cascadia build. I have also seen mention of “Steve’s Rims” in several threads but I have not been able to find a link to them, just the reference. If anyone can direct me, I would also appreciate that information. Thanks for your help.

I H builder Steve, in the vendor section.
PLEASE beware of the forum time and post limits, before you can access to the buy and sell section.
Cheers, Neil.

[rctrucker2]

Thanks doodlebug, found it. The wheels look great and are just what I am looking for. Will have to save up some $$ as they are a little more than I was expecting.

[540-MAN]

I couldn't find it.

[Berman]

I have the same truck, trailer and radio (futaba 4YWD) with the stock servos and mine runs fine, even with a small kid sitting on the trailer. The only time I have ever had a problem with mine shutting off (apart from a flat battery) is with the tamiya/molex plug, replace your battery connections with Deans, Powerpole, Traxxas or whatever your desired plug is, the tamiya ones lose contact easily and are only rated for 7.5 amps. Even if you think the plug is good it can lose contact inside. Mine were not allowing enough current for the MFC01 and kept switching it off.

[540-MAN]

Hi everyone I'm back again to give you all updates. Now the update is I had plans of changing my knight hauler in to a freightliner but that's not going to happen as I fixed the problem of it shutting itself down. The truck has been now sold as a person offered to buy it from me so I sold it to them.

As much I didn't like the new freightliner that has just been released from tamiya I have desided to go and buy one. I looked at them long enough and it is slowly growing on me a little. All I have to do is make a few little changes and I'll start liking it more and more. I have to wait for a couple of weeks for it to get to me though so there won't be any starting photos just yet. I wishing it would hurry up though of getting delivered because I'm really starting to get bored looking at the idiot box (TV).

So that's the updates at the moment I will be posting the progress photos in this thread saves starting a new one.

[540-MAN]

Hi everyone I'm back again it has been awhile since I have posted on here in this thread. I received my freightliner just after my last post in 2014 and still have it. I have updated my trailers for it and it was just last year I have only started painting everything. The painting is not finished yet and there are a few more changes to make as I'm just taking my time with everything.

I will have photos for you soon from the start of the build to the end. But as I have always been told is that nothing never ends as you are always changing something.

[540-MAN]

The starting stages of my build of the Cascadia back in 2014.

http://i1374.photobucket.com/albums/ag412/Shaun_North/ccb8bb16-cb1b-4fad-827e-2344ff52d4e7_zpsjskspnag.jpg (http://s1374.photobucket.com/user/Shaun_North/media/ccb8bb16-cb1b-4fad-827e-2344ff52d4e7_zpsjskspnag.jpg.html)

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0071_zpsohnih7yh.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0071_zpsohnih7yh.jpg.html)

Front axle, servos, springs, shocks and diffs fitted.

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0073_zpsdhhdi9rp.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0073_zpsdhhdi9rp.jpg.html)

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0074_zpsaoycooyr.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0074_zpsaoycooyr.jpg.html)

Motor, wheels, gear box, drive shaft and tanks fitted.

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0075_zpswdexxc3y.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0075_zpswdexxc3y.jpg.html)

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0077_zpsbcxtlugm.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0077_zpsbcxtlugm.jpg.html)

[Berman]

Always nice to build a new truck. :)
Am interested to know what was wrong with your Knight Hauler before you sold it.

[540-MAN]

Always nice to build a new truck. :)
Am interested to know what was wrong with your Knight Hauler before you sold it.

It was shutting down it 3rd gear and full throttle in 2nd it was like the battery was flat because it would start up again. The problem was the battery had a drop cell in it so went and got battery fixed and brought a new one at the same time then it was all fixed before I sold it.

The reason I sold it because a guy offered to buy it from me and I gave in and sold it to buy a freightliner.

[540-MAN]

Body, side skirts and other bits fitted.

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0083_zpsrza3dsyn.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0083_zpsrza3dsyn.jpg.html)

http://i1374.photobucket.com/albums/ag412/Shaun_North/IMG_0084_zpsurss6mxy.jpg (http://s1374.photobucket.com/user/Shaun_North/media/IMG_0084_zpsurss6mxy.jpg.html)