|
|
|||||||
| Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
 |
|
|
Thread Tools | Display Modes |
|
|
|
#1
01-27-2013, 05:03 PM
|
||||
|
||||
Re: 990 cat loader
Is it cement floor there already?
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe 
|
|
#2
01-27-2013, 06:15 PM
|
||||
|
||||
|
Re: 990 cat loader
yea but very rough , when we poured it had to be 1 of the hottest days
 the load came hot to begin with coupled with dry hot stones at 2 " rat slab it was all my dad and I could do to get it raked out . the ledge in the pic is half the base for the fireplace + a cap on the buttress wall. the ground here is tight close to your clays but put sand stone rocks in it . in the dry spell , it takes some time to scratch through with the 307 cat excavator I had . We hit ledge in the north east corner (straight back under the pumbing ) I'm just not sure I want to knowing whats under there . It'll sure be some model engineering fun 
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#3
01-27-2013, 06:39 PM
|
||||
|
||||
|
Re: 990 cat loader
A heated playground for the winter!
 ........lucky dog!  Mario
|
|
#4
02-01-2013, 03:47 PM
|
|||
|
|||
|
Re: 990 cat loader
I'm gonna have to build low pro mining equipment for my crawl space. At best, 18" is all I have at the high end. It would be a great project though. How heavy is the loader IHBuilder?
|
|
#5
02-01-2013, 05:29 PM
|
||||
|
||||
|
Re: 990 cat loader
OK official weight 46.6 lbs without the cab finished . I guessed about 40-50 lbs awhile back
not to far off ( I think I pulled somethin  ) I used to throw 50 lb seed, fertilizer, and lime bags up on a hydro seeder for years so I guess I got a feel for it  I decided to go through with the basement dig can't think of any logical place to store my coal unless I start another building I can just see the township beside , I got some new machines coming on line this year  I need a good proving ground  .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#6
05-27-2013, 10:45 PM
|
||||
|
||||
|
Re: 990 cat loader
started fixing another weak link today . I kept having issues with my valves sticking open and leaking
 The culprit p---- poor tolerances in the valve heads . The leaking was coming from a 6mm ID oring on a 5.8mm OD shaft So Made new 1's out of brass . 3-4 hours setup and tweaking and 1hr run time tops between the lathe and mill .   old  new  thanks for lookin
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
#7
06-16-2013, 11:25 PM
|
||||
|
||||
|
Re: 990 cat loader
whew a little time in the shop with the cad off and the mill off
Did some rearranging with the hydros and electrics . now I can use 2 bats and keep them under the hood . Also no more leaky valves the operator got a bench seat though all nice and tucked under the hood    
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
|
|
| Currently Active Users Viewing This Thread: 8 (0 members and 8 guests) | |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
