Forum: Construction Companies & Worksites
11-13-2017, 10:56 AM
|
|
Replies: 9
Views: 5,959
Re: Deadwood Sand & Gravel
Thank you, I could possibly be into that depending on the work schedule at that time
I had seen one similar to this years ago too when i was hauling material, kinda what i based this off of.
...
|
|
Forum: Construction Companies & Worksites
11-07-2017, 10:18 AM
|
|
Replies: 9
Views: 5,959
Deadwood Sand & Gravel
My stuff finally getting dirty...
https://i.imgur.com/Asevl4y.jpg
https://www.youtube.com/watch?v=ZvnP0iCWVP8&t=334s
|
|
Forum: Construction Equipment
09-06-2017, 08:36 AM
|
|
Replies: 139
Views: 104,321
|
|
Forum: Construction Equipment
09-03-2017, 12:40 PM
|
|
Replies: 46
Views: 19,464
Re: Trommel Build
Thanks guys. I have considered it like some of the other projects. May need to upgrade a few things to try to make this a quicker process. No clue what a reasonable price would be.. pretty big item.....
|
|
Forum: Construction Equipment
09-03-2017, 02:33 AM
|
|
Replies: 46
Views: 19,464
Re: Trommel Build
Thanks Bo, I need that contact info from you cause now I need to ask Santa for some trucks to haul all this finely sorted material around. ;)
|
|
Forum: Construction Equipment
09-02-2017, 05:15 PM
|
|
Replies: 46
Views: 19,464
|
|
Forum: Construction Equipment
09-02-2017, 04:42 PM
|
|
Replies: 139
Views: 104,321
Re: 3D Printed D10T Build
So anyways......
Had a Firgili actuator blow a drive nut a few weeks back..
https://i.imgur.com/QnOpUk5.jpg
Actuonix has taken over now and were very helpful in getting me back together by...
|
|
Forum: Construction Equipment
09-02-2017, 04:31 PM
|
|
Replies: 46
Views: 19,464
Re: Trommel Build
Field test went well, but started to rain before i could record any video. Getting the remnants of Harvey through our area today..So here is a few shots of the site. Side note- This is the first...
|
|
Forum: Construction Equipment
09-01-2017, 05:48 PM
|
|
Replies: 133
Views: 66,009
|
|
Forum: Construction Equipment
09-01-2017, 09:19 AM
|
|
Replies: 46
Views: 19,464
|
|
Forum: Construction Equipment
08-31-2017, 06:58 PM
|
|
Replies: 46
Views: 19,464
Re: Trommel Build
Thanks! Will do.
Thank you. I tried capturing the feel of an older plant maybe built in the 50s, similar to one at a gravel pit we used to haul out of when I used to drive.
I posted a vid...
|
|
Forum: Construction Equipment
08-30-2017, 10:49 PM
|
|
Replies: 34
Views: 5,336
Re: Conveyer Project
Jim, in Imgur click the pic you uploaded then copy and paste the code from the message board option in your post here.
|
|
Forum: Construction Equipment
08-30-2017, 08:31 PM
|
|
Replies: 183
Views: 95,569
|
|
Forum: Construction Equipment
08-29-2017, 05:32 PM
|
|
Replies: 46
Views: 19,464
Re: Trommel Build
Jim, The first thing i wanted to do was make sure that i could dump into the hopper without any issue so measured the width of buckets on my machines. Then yes like you mentioned, i wanted to be...
|
|
Forum: Construction Equipment
08-28-2017, 11:41 PM
|
|
Replies: 46
Views: 19,464
Re: Trommel Build
Thanks Jim, didn't really plan that I was just setting it down on my way to the barn and grabbed the spray can from the garage before I painted and decided to snap a before shot.. before grabbing it...
|
|
Forum: Construction Equipment
08-28-2017, 07:46 PM
|
|
Replies: 46
Views: 19,464
Re: Trommel Build
Spring blocks and new rollers are machined. The initial spring setup was crude but was helpful in getting an idea what the movement was going to be like. Determined a stronger rate spring was needed...
|
|
Forum: Electronics tech
08-17-2017, 10:42 PM
|
|
Replies: 1
Views: 2,698
Carson rotating beacon questions
Have a set of the Carson rotating beacons that I'd like to use without plugging into a receiver. So I tried powering direct from 6 volts and the lights are all on but do not run the sequence /...
|
|
Forum: Construction Equipment
08-11-2017, 10:59 PM
|
|
Replies: 139
Views: 104,321
|
|
Forum: Construction Equipment
08-11-2017, 09:37 AM
|
|
Replies: 139
Views: 104,321
|
|
Forum: Construction Equipment
08-10-2017, 11:39 PM
|
|
Replies: 139
Views: 104,321
Re: 3D Printed D10T Build
Yeah, your not the first person to mention that haha. Its just the track pins squeaking like you said. Cool little bonus I guess. :)
|
|
Forum: Construction Equipment
08-06-2017, 02:09 PM
|
|
Replies: 139
Views: 104,321
Re: 3D Printed D10T Build
Ive been asked this a few times, and i can really only recommend what i know, and i use the Afinia h480 printers, they have been replaced now with the h400. They arent very main stream but are...
|
|
Forum: Construction Equipment
08-06-2017, 11:31 AM
|
|
Replies: 34
Views: 5,336
Re: Conveyer Project
Works like a charm! Ill prob be copying your belt tensioner design when i build mine. Love the dragline too.
|
|
Forum: Construction Equipment
08-06-2017, 09:48 AM
|
|
Replies: 139
Views: 104,321
Re: 3D Printed D10T Build
Jim, yes I printed them and the way I avoided any support was printing them at a 45 degree angle, and a fine resolution. They came out great. I think I may have a pic showing the part orientation. ...
|
|
Forum: Construction Equipment
08-05-2017, 06:34 AM
|
|
Replies: 139
Views: 104,321
|
|
Forum: Construction Equipment
08-04-2017, 11:28 PM
|
|
Replies: 139
Views: 104,321
Re: 3D Printed D10T Build
Autodesk 123D and Tinkercad come to mind and Fusion360, although I'm not sure if that one is free or not. There are some others I'm sure. Plenty of Autodesk tutorials on YouTube to get you started...
|
