Forum: Farm Tractors and Implements
08-31-2022, 05:22 AM
|
Replies: 13
Views: 8,679
|
Forum: Farm Tractors and Implements
08-31-2022, 05:20 AM
|
Replies: 29
Views: 18,551
|
Forum: Farm Tractors and Implements
10-21-2019, 05:46 PM
|
Replies: 29
Views: 18,551
|
Forum: Farm Tractors and Implements
10-17-2019, 07:48 PM
|
Replies: 29
Views: 18,551
Re: Fully 3D printed John Deere 1/10 scratch build
Its nice to have a break from fusion 360 and printing so dived into more software. I had a quick go at the controller. Handy using an android app as there no limit to channels. Also easy 2 way comms....
|
Forum: Farm Tractors and Implements
10-17-2019, 07:13 PM
|
Replies: 29
Views: 18,551
|
Forum: Farm Tractors and Implements
10-17-2019, 06:57 PM
|
Replies: 29
Views: 18,551
Re: Fully 3D printed John Deere 1/10 scratch build
I am assumeing you can install the arduino IDE, connect arduino, find COM port, Wire up display to the I2C pins etc. Below is the code I used. You will require the associated libraries Adafruit GFX...
|
Forum: Farm Tractors and Implements
10-17-2019, 06:50 PM
|
Replies: 29
Views: 18,551
|
Forum: Farm Tractors and Implements
10-16-2019, 05:22 AM
|
Replies: 29
Views: 18,551
Re: Fully 3D printed John Deere 1/10 scratch build
I have done some research and found my 30mm fan throughput is 4.12 CFM. This is obviously not enough. Ideally I would like to treble this so will require a 50mm fan. So a re-design of the enclosure...
|
Forum: Construction General Discussion
10-16-2019, 03:15 AM
|
Replies: 3
Views: 2,363
Re: Bruder 2818 Mack crane
I personally have not seen a crane Mack conversion but seen the plenty Mack tipper truck conversions. The crane looks cool. Looks like a new thread coming. Looking forward to seeing your progress.
|
Forum: Farm Tractors and Implements
10-15-2019, 08:49 PM
|
Replies: 29
Views: 18,551
Re: Fully 3D printed John Deere 1/10 scratch build
I have programmed the OLED display and made a mount to go in the cab. Looks awsum! Made my own 32x32 pixel icons for 4WD, Diff Lock etc. Then managed to drop the OLED and it cracked agghhrrr! New one...
|
Forum: Farm Tractors and Implements
10-11-2019, 07:59 AM
|
Replies: 29
Views: 18,551
Re: Fully 3D printed John Deere 1/10 scratch build
Cab frame complete using 14 seperate parts. Rear window functional and will be connected to a servo. Wasnt the most efficient way of making the cab but saved a ton of supports when 3D printing. I did...
|
Forum: Fire and Rescue and Emergency Vehicles
10-08-2019, 10:05 AM
|
Replies: 131
Views: 65,726
|
Forum: Farm Tractors and Implements
10-08-2019, 03:25 AM
|
Replies: 29
Views: 18,551
|
Forum: Farm Tractors and Implements
10-08-2019, 03:14 AM
|
Replies: 29
Views: 18,551
|
Forum: Farm Tractors and Implements
10-06-2019, 03:33 PM
|
Replies: 29
Views: 18,551
Re: Fully 3D printed John Deere 1/10 scratch build
The rear 3 point linkage is done. I am quite pleased how it turned out. Need to think of how to attach a PTO shaft now. I will probably just have a square drive and 2 grub screw to lock PTO shaft on...
|
Forum: Farm Tractors and Implements
10-04-2019, 03:24 AM
|
Replies: 29
Views: 18,551
Re: Fully 3D printed John Deere 1/10 scratch build
I use fusion 360. Used to use sketchup a lot but soon converted when I realised there are plenty of complicated parts coming up and needed to model joints and moving parts. Very time consuming as I...
|
Forum: Farm Tractors and Implements
10-02-2019, 07:14 PM
|
Replies: 29
Views: 18,551
Fully 3D printed John Deere 1/10 scratch build
Hi Everyone
Heres the start of my first build. I have decided to fully 3D print the whole build where I can as I have two CR-10 printers to be used. Its based on the round cab series John Deere as...
|
Forum: Welcome New Members
10-02-2019, 05:48 AM
|
Replies: 0
Views: 3,312
New from Wales, UK
Hello everyone. New member here 30 from the UK. Finally started my first build. thread to follow. Looked through these forums for years now and finally started my own build. Got my passion from a...
|