Low load step deck

[FreddyGearDrive]

Been wanting to build one of these for a while.

But could never find the right tires & rims to make me happy.

Well found some that will work fine,But!there wedicos.So first had to make some longer axle shafts.

Then,do some frame butchin.


Now some axles.

Upper deck frame.


Now some styrene work.












Few more pieces,landing gear,Then the decking!
Thanks for lookin!
FGD

[cummingsman29]

Nice job, were did you get the trailer tires?

[RCLogger]

Nice Freddy
You sure make working with stirine look easy. Those trailers must scrub the tires off easy with that long distance between them ?

greg

[Espeefan]

Looks really good, Fred. You sure made some progress with that thing, despite being busy starting this forum up about the same time! None the less, it looks fantastic!

[Bigrigger]

Wow! Great progress Freddy! I love that tractor too! My favorite! I got to get one of those center tail light mounts! Maybe a spoiler too, are that what those are called? I'm forgetting.... Well looks great as always Freddy! -Trucker

[JAMMER]

Fred your just like GE progress is your most important product, and it looks good to. Ed

[Stylin n profilin]

Freddy..I said it when you started this board...i'll say it again...ALL HALE FREDDY!!!

[Pipeliner_970]

I really like this one Freddy, it's comin out awesome!!! It reminds me of a Doonan drop that i pulled a few times for an outfit i used to work for, It had the sliding rear axle and 17.5" wheels.

Say speakin of that sliding rear axle, as much as you like all your trick little mechanical bits and what not, you outta make that rear axle slide on this one, eh??

The one I pulled was similar to this:

[FreddyGearDrive]

Thanks Guys!
Donny,purchased from pmd.
Sparkycuda,the ole-J-B weld & some screws.
P/L970,Thanks for the pic.Might try that on the next trailer.
Man! This sucks not havin any time to build But did manage to sneek in a few hrs & got the back end done.





Can't believe it's taken this long to finish this trailer. Plus haven't touched my Atlas truck in WEEKS!
FGD
WE NEED MORE SMILES!

[unc]

Originally Posted by Pipeliner_970

I really like this one Freddy, it's comin out awesome!!! It reminds me of a Doonan drop that i pulled a few times for an outfit i used to work for, It had the sliding rear axle and 17.5" wheels.

Say speakin of that sliding rear axle, as much as you like all your trick little mechanical bits and what not, you outta make that rear axle slide on this one, eh??

The one I pulled was similar to this:

It slides good on the ice road. unc

[RAIDERS]

Thats one nice trailer!!!

[sparkycuda]

Really great, as usual. When you step-cut the frame rails and bent the flanges to match the angle cut, how did you secure the flange to the rail...super glue, aluminum solder, other?

Looking forward to meeting you at Indy.

Ken Sharp

[Espeefan]

That thing looks awesome, Fred!

[Tamiya Cowboy]

Hey buddy looks good. Little sway back but good. LOL

Hey! Freddy hope you had permission to find some time to build Looking good.

Steve.

[JAMMER]

Fred progress is our most important product. Ed

Didn't you suggest this same trailer for my truck?

[Hos1880]

Freddy

This is an awesome build what did you use to widen the axles with and are they treaded on the inside?

Merritt

[FreddyGearDrive]

Thanks Guys!
Losi,that's the one!
Hos1880,they where hollow tubes that I cut & threaded.
Well snuck in a couple of hrs & got the decking cut to length.



Thanks for lookin!
FGD

[fhhhstix]

The trailer is looking real good their Freddy and the styrene is getting addictive isn't it.