Cool tranny mod for front wheel drive (Vid added)

[SmallHaul]

I made this up today, it is no done yet though. I ordered flanged bearings for it and I have to make nice stand offs for it but, it actually works as is.

[SmallHaul]

Short vid:

http://www.youtube.com/watch?v=6KrCl8c0uhI

[SmallHaul]

I made a cover for it. I will use some clear silicone to seal it up when I get the bearings installed:

[Bob From Downunder]

Hi Scott this is fantastic, well thought out and has a lot of protential for 6x6 users. Can you please tell me where you bought the gears from. This is what I have been searching for. All I need to do now is find a way to disconnect the front drive.

Bob

[SmallHaul]

Originally Posted by Bob From Downunder

Hi Scott this is fantastic, well thought out and has a lot of protential for 6x6 users. Can you please tell me where you bought the gears from. This is what I have been searching for. All I need to do now is find a way to disconnect the front drive.

Bob

You can find all of the gears on ebay. I used 32 pitch.

I used two 18 tooth pinion gears (5mm bore)
http://cgi.ebay.com/Traxxas-Tra5644-...efaultDomain_0

and one 22 tooth pinion gear
http://cgi.ebay.com/Traxxas-E-Maxx-2...ts_Accessories

The size of the center gear will not change the ratio as long as the 2 outside gears are the same. So, you could run a 28t 32p gear for the idler gear and that would lower the final output shaft a little.

28t 32pitch 5mm bore gear:
http://cgi.ebay.com/CASTLE-CREATIONS...ts_Accessories

[ihbuilder]

Originally Posted by SmallHaul

You can find all of the gears on ebay. I used 32 pitch.

I used two 18 tooth pinion gears (5mm bore)
http://cgi.ebay.com/Traxxas-Tra5644-...efaultDomain_0

and one 22 tooth pinion gear
http://cgi.ebay.com/Traxxas-E-Maxx-2...ts_Accessories

The size of the center gear will not change the ratio as long as the 2 outside gears are the same. So, you could run a 28t 32p gear for the idler gear and that would lower the final output shaft a little.

28t 32pitch 5mm bore gear:
http://cgi.ebay.com/CASTLE-CREATIONS...ts_Accessories

Scott , Your right till you get to "would lower the final output shaft a little." It dose not matter what size Idler gear as long as the input and output are the same you would not change the ratio . Now If you are referring to changing the out put to a 28 tooth then yes you would lower the ratio. All Idler gears do is keep the output same rotation as the input . But very good Idea as the same for willy ( custom rc models ).

IHSteve

[SmallHaul]

Steve, When I said "would lower the final output shaft a little." I meant lower the height of the output shaft not the ratio.

[ihbuilder]

Originally Posted by SmallHaul

Steve, When I said "would lower the final output shaft a little." I meant lower the height of the output shaft not the ratio.

Sorry my bad no offense

IHSteve

[Bob From Downunder]

Thanks for your info Scott, I just ordered this morning from RC4WD a disconect unit and some gears so I will play around with it when they arrive. All part of the enjoyment I suppose.

Bob

[Bob From Downunder]

thanks a million Scott, I'll have a go at building one.

Bob

[9W Monighan]

I think the extra axel driving will make climbing steep grades much more easier.

[Bob From Downunder]

no worries mate time I have and the willingness

thanks for all your help, very appreciated.

bob

[Blueshirt]

I'm always jealous when I see someone who has the talent to make somthing like this instead of buying it. Nice Job!