![]() |
|
Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
![]() |
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
![]()
Another fine digger coming up, Like that weight with the logo in it.
How many times do you have to change setting or can you make it all at once? Dan |
#22
|
||||
|
||||
![]()
Az , Nate thank you
Dan, thank you , 1 setup as of now all done by 3D milling . I'm going to have to set it on the 2* taper from top to bottom to clean up the logo . A sin plate would be nice right now ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#23
|
||||
|
||||
![]()
I let it finish up last night with the lights out then finished it in an hr this morning. this is 4/5th of it so far .
![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#24
|
||||
|
||||
![]()
sweet!
|
#25
|
||||
|
||||
![]()
Lookin good Steve.
![]() What does it weigh? Would it be too hard on tools to do it from steel? I have nearly 11lbs of counterweight on the 850 and there are times it's not enough. How far back from center is your counterweight? I'll measure mine to compare.
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#26
|
||||
|
||||
![]() Quote:
![]() :edit: I'm finding it hard to believe only 6 lbs it feels much heavier . It has about the same cubic inch volume as a 20 lb sledge and feels about half .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#27
|
||||
|
||||
![]()
13" from center pivot?
Mine is 9.5" & the entire length of the house is 16.5".
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#28
|
||||
|
||||
![]()
yes , from the center of pivot . From front of cab to back of counter weight is 17.80" X 10" wide . the counter weight is 5" high what is the diameter of your front idler and sprocket ? Mine are 3" major dia with a 2.6" DP for the sprocket .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#29
|
||||
|
||||
![]()
Front idler is about 3", maybe a bit more... difficult to see clearly with the tracks on & me standing on my head to look.
![]() ![]()
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#30
|
||||
|
||||
![]() ![]() ![]() All done now ![]() ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#31
|
||||
|
||||
![]()
Oil tanks for both pretty much done . pics from raw block to finish tank . no pics of the chip pile .
![]() ![]() ![]() ![]() ![]() ![]() thanks for looking
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#32
|
|||
|
|||
![]()
Steve,
Did you hog out the block for the tank and is that your filter? What 3D software are you using and do you like it? Last edited by catmack; 02-24-2013 at 03:07 PM. Reason: Insert omission |
#33
|
||||
|
||||
![]()
But i wanted to see the chip pile
![]()
__________________
Hi my name is Aaron.... And i'm a truckaholic! |
#34
|
||||
|
||||
![]() Quote:
![]() Quote:
![]() ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#35
|
||||
|
||||
![]()
You need your own smelter now Steve!
|
#36
|
||||
|
||||
![]() ![]() |
#37
|
||||
|
||||
![]() Quote:
![]() HA HA , Reg , yea I could start casting the daytons , It's just quicker to mill them
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#38
|
||||
|
||||
![]()
Nice work Steve
You are in the big league now, your skills are # 1 These machines will be moving alot on material come spring... greg |
#39
|
||||
|
||||
![]()
Very impressive.
Just curious, but for those of us who know nothing about machining, where does one buy a giant block of aluminum like that? Last edited by FlyingBeagle; 03-01-2013 at 05:43 AM. Reason: Typo |
#40
|
||||
|
||||
![]()
thanks Greg they should be ready for the fall time . At least 1
Quote:
![]() http://www.onlinemetals.com/merchant...999&top_cat=60
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|