![]() |
|
Construction Equipment If it digs, pushes, hauls dirt "off road" post it here. |
![]() |
|
Thread Tools | Display Modes |
#41
|
|||
|
|||
![]()
Hi Tom Seilbagger here on the form did a D8 with cables. Ed
|
#42
|
|||
|
|||
![]()
http://www.rctruckandconstruction.co...662339&thumb=1 Seilbagger Hi Tom Seilbagger did a D 8 with cable lift blade. Ed
|
#43
|
||||
|
||||
![]()
thanks fellers.
![]() ![]() ![]() ![]() ![]() ![]() Oh, duh need 2 per cylinder ![]() ![]() ![]() ![]() ![]() and nice to have a decent vice on this toy ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#44
|
||||
|
||||
![]()
Steve it's going good over there..........Carry on Please
![]() |
#45
|
||||
|
||||
![]()
Looking good Steve!
![]() Any plans to make a wider wishbone to move tracks away from body?
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#46
|
||||
|
||||
![]()
Joe, the track frames will stay where they are . On the real machine the track pads are off set on the chains . I plan to mill new tracks in the future. They're designed and programmed . It's just a matter of devoting the mill time
![]() Finally got all the cylinder parts done ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#47
|
|||
|
|||
![]()
Looks like you have put a lot of hours in this model steve, but it will be well worth it. Great job.
|
#48
|
||||
|
||||
![]()
How much offset?
Lmk when you decide to do the links, I might be interested in helping you offset your costs by getting a set. ![]()
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
#49
|
||||
|
||||
![]()
Move the pad out by 1 hole on the link . I could do it with these ,I just need to drill 2 more holes per pad . I'll keep you in mind .
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#50
|
||||
|
||||
![]()
few more
![]() ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#51
|
||||
|
||||
![]()
Steve,
Your gonna need to train a aux operator to manage all that stuff! ![]() Jim |
#52
|
||||
|
||||
![]()
Tell me about it. Jim
![]() ![]() ![]() ![]() ![]() ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#53
|
||||
|
||||
![]()
Dang!! Lots of hoses n fittings!! Looks pretty cool!!!
__________________
Always wasting money, as the wife says. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#54
|
|||
|
|||
![]()
Steve-the dozer is looking good. Seems like a complicated build to me but probably not for a machinist like you. Nice work!
|
#55
|
|||
|
|||
![]()
I have a quick question for you! When soldering on the rams does that effect the internals?? I was told if u heat them up they have to be re-honned?
|
#56
|
||||
|
||||
![]()
hone after soldering . the gland end on mine are threaded
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#57
|
||||
|
||||
![]()
How the heck to take a video while operating a 6 way blade dozer
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#58
|
||||
|
||||
![]()
New hood ,from mill machine to finished painted part and grill . All the black painted except the blade (need sandblasting ) . Gps poles made . And a comparison pic of the td40 next to the 6
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Took me 3 tries to post this ![]() ![]() ![]()
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#59
|
||||
|
||||
![]()
Wow that's impressive! Hard to see an Izzy dozer in there.
|
#60
|
||||
|
||||
![]()
The Dresser looks like it's in a different scale!
![]() ![]()
__________________
Sharing knowledge is one thing that defies basic arithmetic logic --- the more you share, the more you get! Joe |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|