|
Metal forming & tools If it bends,twists,welds,cuts & turns metal.Post it here |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
s&f + DOC for a .010 endmill
just checking to see what you all that have done this your whole life think
For DOC I'm thinking .005 Feed rate @ 1in/min s. speed @ 4500 rpm . to fast , yes / no ?
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#2
|
||||
|
||||
Re: s&f + DOC for a .010 endmill
was any of that english????
__________________
Michael also known as "The Crimson Corsair" To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#3
|
||||
|
||||
Re: s&f + DOC for a .010 endmill
OK so ya need a legend
S&F = speeds and feeds DOC = depth of cut
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#4
|
||||
|
||||
Re: s&f + DOC for a .010 endmill
thanks -- now I know what I don't know
__________________
Michael also known as "The Crimson Corsair" To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#5
|
|||
|
|||
Re: s&f + DOC for a .010 endmill
Greatly depends on the endmill. If its a short stubby and well supported you're probably on the slow side. I've played with some small bits before and even my 10k rpm spindle is too slow
__________________
Jeff |
#6
|
||||
|
||||
Re: s&f + DOC for a .010 endmill
it's from Frank Mari .010 dia 2 flute sqr Miniature Carbide Finisher .03 L.O.C I broke 1 just putting it in the collet droped out of my clumsy hands
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#7
|
|||
|
|||
Re: s&f + DOC for a .010 endmill
Been there done that. Just hold them the wrong way and they break.
I've gotten some small mills from Harvey tool, seem to have a failry large selection and you can get the minimum length of cut that you need to get the strongest possible. Mari has good stuff too. Whats you're Axial engagement? if that is tiny, can probably up the DOC a bit
__________________
Jeff |
#8
|
||||
|
||||
Re: s&f + DOC for a .010 endmill
Coolant or dry and what material? DOC and s&f don't sound to bad.
__________________
LYNN |
#9
|
||||
|
||||
Re: s&f + DOC for a .010 endmill
Quote:
I'm just trying to get over the braking phobia Jeff I got a little ingraving to do on the haul truck hubs If it take 3 hrs while I'm doing something else , I don't care
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#10
|
|||
|
|||
Re: s&f + DOC for a .010 endmill
I run 90deg single flute engravers with .005 tip to depth of .010" to .015" at 10k rpm and 15ipm feed, 30ipm plunge in 6061 if that helps at all
__________________
Jeff Last edited by pugs; 10-11-2011 at 10:53 PM. |
#11
|
||||
|
||||
Re: s&f + DOC for a .010 endmill
thanks Jeff & lynn I'm going to give this a try
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#12
|
||||
|
||||
Re: s&f + DOC for a .010 endmill
well you tell me
__________________
RIP FreddyGearDrive 2-12-59/12-19-11 To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. |
#13
|
|||
|
|||
Re: s&f + DOC for a .010 endmill
Looks sharp
__________________
Jeff |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|