- Gooseneck (2 replies)
- 1/16 Axle with Differential needed (15 replies)
- Leimbach pistons repair on 966G (6 replies)
- Independent Suspension on five axles (4 replies)
- TLT Axle Differential - Same as others? (1 replies)
- Locking differentials (17 replies)
- Bearings in 3-speed gear box (8 replies)
- UNGLUE tires from rims (1 replies)
- 1:16 GMC Flatbed RC Driveline (1 replies)
- Magnetic suspension (1 replies)
- Winch set up? (13 replies)
- Integy Locked diff ratio (0 replies)
- Hydraulic Ram (16 replies)
- gear reductions? (6 replies)
- cut down tamiya semi trans to 2 speed ?? (1 replies)
- From 6x4 to 6x6 - Euro truck (0 replies)
- Liebherr LR634 Track Loader HYDRAULICS (9 replies)
- Tamiya diff gears options (1 replies)
- HELP! Shapeways Lift Axle (5 replies)
- I'm puzzled (5 replies)
- 1/14 Eco Drive CVT TRansmission (6 replies)
- motorized support legs (4 replies)
- cable retract (1 replies)
- Stahl dozer gear boxes and drive motors (19 replies)
- Servonaut motor help (5 replies)
- Cable machines, what is your rigging? (0 replies)
- CARSON GEAR MOTOR 907056 (8 replies)
- DIY Linear Actuator or... (9 replies)
- Front driven axle (8 replies)
- Tamiya bolt on reduction gear (74 replies)
- Hydraulics (27 replies)
- Axel question (1 replies)
- Rear axles for scratch build (5 replies)
- 1/14 Tamiya Gearbox Assembly (12 replies)
- King Hauler driveshaft length? (5 replies)
- Rc4wd rims (1 replies)
- Need help with semi truck gear ratios and front wheels (2 replies)
- Tamiya 6T pinion (3 replies)
- What kind of motor need in PMD reduction 4:1 ? (7 replies)
- motor speedy combo to weight ratio. (5 replies)
- widening rear semi axle? (2 replies)
- RC Linde H40D Forklift (1 replies)
- single speed metal tranny question (4 replies)
- Tri-Axle Set-up Help (4 replies)
- Diff lock question (1 replies)
- Help (3 replies)
- driveshaft support bearing (2 replies)
- Heavy Duty Rear Springs (2 replies)
- PMD GRU installation (0 replies)
- need a geardrive (2 replies)
- Lockers (2 replies)
- simple device to build cheap and exactly leave springs (12 replies)
- Screw drive for Tipper/Dump truck.. (5 replies)
- Rc4WD 16:1 pinion tooth count? (0 replies)
- Reduction question(again) (10 replies)
- Super single tires (6 replies)
- Tamiya 3 speed transmission grease? (6 replies)
- Integy Axles (3 replies)
- RC4WD Semi Diff (15 replies)
- RC4WD Gear Reduction (8 replies)
- Transmission options (24 replies)
- Tranmission E Maxx? (8 replies)
- TLT axle size (1 replies)
- Driven front axle options (4 replies)
- locked differentials (25 replies)
- Tranny help!!!!!! (7 replies)
- Locked diffs and suspension travel (4 replies)
- Anyone seen this yet? (3 replies)
- Tamiya mechanical legs - using with radio (8 replies)
- Gears (2 replies)
- Trans. Gears (3 replies)
- RC4WD R2 Transmission (1 replies)
- Noisy transmission...... (12 replies)
- Integy axles for Tamiya semi's (24 replies)
- Integy complete axle set (2 replies)
- 2 shift or not 2 shift? (11 replies)
- Is it the tranny,the gru, or me? (3 replies)
- PMD tranny in globeliner (4 replies)
- Truck way too fast (3 replies)
- Transmission Question (4 replies)
- 3 speed transmission question? (4 replies)
- 3 speed tranny's and ball bearings... NOT recommended? (8 replies)
- Tamiya 3 speed vs Wedico single Speed. (7 replies)
- TLT Axle Question (2 replies)
- What goes in between (8 replies)
- drive shaft shorten (2 replies)
- GD-600 Gear Reduction Retro for King Hauler (11 replies)
- Dual Drive Motors? (7 replies)
- Transmission help or suggestions (7 replies)
- three speed gear ratio (4 replies)
- 3 speeds (8 replies)
- Tamiya Semi - Powering the Steering Axle (11 replies)
- 3 Speed Gear box (3 replies)
- How To Custom Drive Shaft (36 replies)
- driveshaft questions (3 replies)
- Front drive axle (9 replies)
- how do you lock the rear (16 replies)
- Transmissions & Transfer Boxes for 6x6 (23 replies)
- Too fast!! (18 replies)
- Driven front axle options? (76 replies)